Search

Type: Posts; User: tiderider

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Straight Brass Male with barb end for head bleeder hose. Size/Specs.

    Hi, would anyone know what are the dimensions for the straight brass fitting which has a male threaded end on 1 side and a barb end on the other for the cooling system bleeding off the back head...
  2. I got PLAY TIME on mine. I get many asking if...

    I got PLAY TIME on mine. I get many asking if they can play with me... LOL..
  3. Wow! This has really become a truly helpful...

    Wow! This has really become a truly helpful thread.
    The big players come out with great knowledge off season!
    Sounds like I am pretty much dead on with my AFRs and should simply stick to 94...
  4. I have a RRFPR, I am just concerned that lowering...

    I have a RRFPR, I am just concerned that lowering the pressure to perhaps 55 psi instead of 58 psi to achieve the leaner .5afr may also reduce fuel supply to the 60lb injectors at 8500 rpms to a...
  5. Hi, thank you for the info. I am unable to see,...

    Hi, thank you for the info. I am unable to see, read or change ignition timing with my 2007 Siemens ECU and Riva tune with PLX logger set up. The engine has been rebuild with .5mm oversized pistons....
  6. Its a risk item.. I rebuild one a while back that...

    Its a risk item.. I rebuild one a while back that had many years, and with 150 hours on the original rebuild (Most updated kit). It was just like new, even the slip was dead on. I guess its a combo...
  7. I am aware of this. But will the 10% ethanol in...

    I am aware of this. But will the 10% ethanol in the Washington 92 pump fuel help AFRs?
  8. Not the same quality. That's for a stock...

    Not the same quality. That's for a stock impeller. Solas concord is 15/21 for a stock application.. you should get a good 100 rpms with using a solas.... The 15 degree core will give you easily an...
  9. Without retainers upgraded and flywheel bolts as...

    Without retainers upgraded and flywheel bolts as well... I wouldn't spin it more then 8400 rpms. Stock is 15/21. I would go 15/20 with a solas concord to give you an extra 100-150 rpms. Or simply...
  10. 92 Octane pump with ethanol and Torco +4 Octane for 96

    Trying to get my AFRs up a tab, like .5 so it would be in the mid/high 12s at idle and 12.2ish at wot with 8500 rpms and 13psi.

    Presently with the use of 94 Octane with no ethanol is giving me...
  11. Replies
    9
    Views
    514

    I pour 1 gallon of high quality RV antifreeze...

    I pour 1 gallon of high quality RV antifreeze into a pail and with a bilge pump, hose, fittings to hook up onto the flush port. Bilge pump wiring is long enough to reach the battery and has a switch...
  12. $$$$

    $$$$
  13. I sure hope you didn't pay a lot for it.. Sounds...

    I sure hope you didn't pay a lot for it.. Sounds like its going to cost you a LOT of $$$$ to get it started, never mind running..
  14. Replies
    2
    Views
    132

    Hey, thank you for the quick response. I was able...

    Hey, thank you for the quick response. I was able to put a meter on the wiring and your correct!

    Do you know if the craft would operate normally if the switch is bypassed (Always Closed). Its for...
  15. Replies
    2
    Views
    132

    Neutral switch Open or Closed

    Hi, would anyone know if the neutral switch is normally open when the craft's lever is in neutral and is closed when put into forward?
    Or is it closed in neutral position and opens when the craft...
  16. Try on Ebay.com and not ebay.ca.. It comes up...

    Try on Ebay.com and not ebay.ca.. It comes up when searched on ebay.com. No Part number, just states its exclusively available from IJDMTOY.
    ...
  17. Here you go Ebay item number 372795839051...

    Here you go

    Ebay item number 372795839051 Unable to attach long link...
  18. Got it done. Pretty much, do a parallel feed - +...

    Got it done. Pretty much, do a parallel feed - + from the fuel pump relay's coil voltage feed to the "time delay on" coil voltage feed. Simply ran a dedicated circuit through the time delay on relay...
  19. Auto On/Off for AFR gauge and sensor assembly

    I am tired of having to remember if I left the AFR sensor and gauge on after riding or forgetting to turn it on initially as well.

    I upgraded my fuel pump which now has a relay that gets operated...
  20. I think they are saying they cannot tune your...

    I think they are saying they cannot tune your boat without doing test and see.. Keep us posted..
  21. I am wishing the best for you. I was able to...

    I am wishing the best for you.
    I was able to pull information off my ECM which the tuner is looking for with a candooPro. Hopefully its the correct information and he can work with it.

    Good Luck.
  22. Its an RXT 2007.

    Its an RXT 2007.
  23. 50-70 tune files were attached for me and only...

    50-70 tune files were attached for me and only one is decent with the sole issue of it not starting up when the engine is hot... The 95 XP800 is not a 4 stroke... I recalled seeing 17 AFR at 7000 rpm...
  24. So it appears that sending off your ECU to Riva,...

    So it appears that sending off your ECU to Riva, may or may not work for you. It all sounds like they are guessing...

    I'm just wondering if running it rich at 11.5ish at wot 11-13 psi can melt a...
  25. A logger, logs PSI pressure, AFRs, RPMs,...

    A logger, logs PSI pressure, AFRs, RPMs, temperatures etc I was not able to log the most important thing (Ignition timing) with the siemens ECU. Riva said its not available to view on the seiemns...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4