Search

Type: Posts; User: imp0ster

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    5
    Views
    301

    That's beautiful Scott. However it's tax evasion...

    That's beautiful Scott. However it's tax evasion and I'm telling
  2. Sticky: runs off the broken hopes and dreams of BRP...

    runs off the broken hopes and dreams of BRP customers
  3. Sticky: Engages senior citizen mode. Puts on left...

    Engages senior citizen mode. Puts on left blinker when you're turning right and goes 15mph under the speed limit and swerves in front of you when you try to pass
  4. Replies
    24
    Views
    1,168

    guys this is not normal. My 19 hit hard as Fk...

    guys this is not normal. My 19 hit hard as Fk coming down from about 6ft in the air at 76mph. If you're going to repair it you need to cut the damage into a v and fill it with epoxy resin and...
  5. DO not tune until you see knock. Tune it safely...

    DO not tune until you see knock. Tune it safely but agressive. If you're tuning it til KR and pull timing back the first time you get bad gas you'll toast your motor. I learned this in my grand...
  6. Replies
    18
    Views
    1,021

    Drill new holes and go one click below what Riva...

    Drill new holes and go one click below what Riva offers
  7. Replies
    18
    Views
    1,021

    not a chance. ST3 hull. They make a world of...

    not a chance. ST3 hull. They make a world of difference and start in the middle if you buy them
  8. If you guys are really on the limit like that...

    If you guys are really on the limit like that then you need to just run 100LL like I did instead of blending. Torco will orange out and waste your plugs but it does work. C16 is great but be...
  9. Replies
    7
    Views
    470

    Good for you. I did the same and lost 25. 205...

    Good for you. I did the same and lost 25. 205 now and I feel much better at the end of the day and can take more of a beating out there. It's worth it. Also, Epstein didn't kill himself.
  10. Replies
    7
    Views
    470

    you would notice 80lbs. That's kind of the...

    you would notice 80lbs. That's kind of the difference between a full tank and empty tank. It would handle better, accelerate harder and gain you some top end. Problem is you'll never remove 80lbs....
  11. Replies
    27
    Views
    1,469

    If your fingernail can catch it a bore hone won't...

    If your fingernail can catch it a bore hone won't matter
  12. Replies
    9
    Views
    543

    put your trim in the middle or a notch up and...

    put your trim in the middle or a notch up and shift your weight back. You need an intake
  13. Replies
    10
    Views
    414

    if it's loose pack it with epoxy, drill the epoxy...

    if it's loose pack it with epoxy, drill the epoxy and run in a small self tapper
  14. Replies
    16
    Views
    1,607

    So speaking from personal experience. I kicked me...

    So speaking from personal experience. I kicked me and my girlfriend off my ski about 76mph when it started leaning hard left around 6ft in the air. I was sucked into a wake and hit a cross wake. ...
  15. only doo that has it is the GTX. F BRP for not...

    only doo that has it is the GTX. F BRP for not including it in the T-X. You pay top dollar and they still leave out options.
  16. So when you prep a mold if you don't use enough...

    So when you prep a mold if you don't use enough releasing compound the hull will stick in the mold and the only way to remove it is was force. Lots of force since there is also a good deal of...
  17. Replies
    37
    Views
    2,637

    roughed up the plastic with 60 grit and gorilla...

    roughed up the plastic with 60 grit and gorilla glued the grip on. Packed the crevice with plastic epoxy and set a wider screw in. Did it to both grips. I pulled on it as hard as I could a day...
  18. Replies
    37
    Views
    2,637

    I had them preemptively replace the ring since I...

    I had them preemptively replace the ring since I was spinning out of true. I fixed my own grip. Their repair is to use a bigger thread bolt and pack the bar with epoxy which is dumb AF.
  19. Replies
    37
    Views
    2,637

    Dealer aligned my engine, replaced the carbon...

    Dealer aligned my engine, replaced the carbon ring with the new updated kit, flashed the ECU to correct the IBR trying to kill me issue and replaced the intake grate bolts/nuts. What's next!?!? THE...
  20. Replies
    22
    Views
    1,229

    don't touch the cam unless you're ready to...

    don't touch the cam unless you're ready to datalog and dick with your timing and fueling table. You'd be better off just adding boost and a canned tune meant for the charger you pick
  21. Replies
    37
    Views
    2,637

    Exhaust valve? Weird the SC 300 is dropping...

    Exhaust valve? Weird the SC 300 is dropping intakes unless their just garbage. Time to call ferrea again
  22. Replies
    5
    Views
    253

    not really. Salt water and the sun would eat it...

    not really. Salt water and the sun would eat it up if you ride salt. Give it a shot and let everyone here know how it goes and how it sounds
  23. Replies
    5
    Views
    253

    only works on naked bars. Dielectric doesn't get...

    only works on naked bars. Dielectric doesn't get used with water exposure. You need liquid electrical for that. Use die electric in the engine compartment on sealed connection and on the porcelain...
  24. Replies
    125
    Views
    21,074

    Jim is here as are a few CRT conversion skis. ...

    Jim is here as are a few CRT conversion skis. There's an annual ride through St Joseph Sound with about 100 skis tearing it up. I went once and never again due to the dumb shit I saw.
  25. Replies
    125
    Views
    21,074

    I plan on printing off some 600hp stickers for my...

    I plan on printing off some 600hp stickers for my doo. 600 is crazy. I'll have to put a roll bar on my ski in case I flip it
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4