Search

Type: Posts; User: SURFnTURF

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    1,686

    Sounds like either or both the raves are not...

    Sounds like either or both the raves are not opening or water lines are reversed into the pipe. Or rear water box controller isn't reducing water cooling at higher rpm. It should always flow but...
  2. Replies
    13
    Views
    1,130

    You have rebuilt the fuel pump incorrectly or...

    You have rebuilt the fuel pump incorrectly or have fuel ⛽ lines wrong. The only time I have ever needed a 951 using electric fuel pump was using hi rev twin pipes that revved over 7700 in flat water....
  3. Replies
    13
    Views
    1,130

    Yea, hahaha….

    Yea, hahaha….
  4. Here is the cooling diagram showing correct OEM...

    Here is the cooling diagram showing correct OEM flow
  5. Replies
    4
    Views
    283

    12.3 volts is equal to 50% battery charge 12.8...

    12.3 volts is equal to 50% battery charge

    12.8 ------------100%
    12.7-------------90%
    12.6-------------80%
    12.5-------------70%
    12.4-------------60%

    Your Battery is stuffed,grab a AGM...
  6. Replies
    27
    Views
    1,143

    I had similar issue with a 2000xpl, front...

    I had similar issue with a 2000xpl, front cylinder would cut out at 4k and above. Was a bad coil, ran fine for 2 months then exact same issue. Turned out to be bad earth (Ground) in the black box....
  7. Easy to check to see if its a water issue , run...

    Easy to check to see if its a water issue , run it at wot and cut the throttle and ignition.Pull the pipe,you should see water droplets or water crystals dried up inside the pipe before the water...
  8. Can be head gasket,Manifold gasket or head pipe...

    Can be head gasket,Manifold gasket or head pipe gasket
    I have had cylinders rusting from between the liner and aluminum casting
    and they bow the liner in which water can leak down between from the...
  9. 2000 SEADOO 951 Di CODE P0105 & P0106 The...

    2000 SEADOO 951 Di CODE P0105 & P0106


    The pressure sensor is in the mag side of the throttle body, the air temp sensor is in the pto throttle body intake boot.
    Try disconnecting the MAPS plug...
  10. Replies
    15
    Views
    900

    You checked for any water in the fuel ⛽?

    You checked for any water in the fuel ⛽?
  11. You can re use them. If you haven't moved the...

    You can re use them.
    If you haven't moved the mounts just bolt it back in the same position.
    I only realign if the centre mount bearing is swapped out or new mounts are used
  12. 951 driveline are the beefiest and strongest of...

    951 driveline are the beefiest and strongest of all the 2 stroke models,once aligned free revving them doesn't hurt them at all.
    Rev limiter is set at 7200 + or - 50 rpm
    Being a "Master Sea-Doo...
  13. Makes no difference hitting the rev limiter in or...

    Makes no difference hitting the rev limiter in or out of the water, some like to think they know more than others,dont worry about it
    As myself says above, try new plugs
    I have had new plugs (a...
  14. Replies
    14
    Views
    1,990

    No, you have it all wrong how the water is used...

    No, you have it all wrong how the water is used on a 951 pipe

    The stock system is not really a water injection system compared to the aftermarket products ,the mid pipe water point with its 3mm...
  15. Replies
    14
    Views
    1,990

    No you have it all incorrect Water Injection...

    No you have it all incorrect

    Water Injection is about loading the pipe with water not trying to dry it out
    No matter how much you dry out the pipe it wont give you any more rpm as Seadoo have...
  16. Replies
    14
    Views
    1,990

    Water into the stinger will do almost nothing to...

    Water into the stinger will do almost nothing to the return exhaust pulse. It needs to be in the head pipe so as to allow the water droplets to have an effect on the returning pulse back into the...
  17. Riding is usually not at idle

    Riding is usually not at idle
  18. Have had detonation do this as well.......

    Have had detonation do this as well.......
  19. Replies
    12
    Views
    1,068

    Try opening up the low speed adjuster screws 1/4...

    Try opening up the low speed adjuster screws 1/4 turn and see if it helps .It may be just the transitioning of the fuel circuits from low to high
  20. Replies
    0
    Views
    251

    WTB 2000 xp limited steering cable

    After a good quality 2000 XPL steering cable,has to be good as its for my personal ski.
    Need to ship to Adelaide Australia ?????????????????????? trevornhhi@adam.com.au
  21. Replies
    21
    Views
    2,281

    Make sure they are resister plugs with the "R" in...

    Make sure they are resister plugs with the "R" in the code.
    I once had a box of 12 plugs NGKs BR8ES that the whole box was faulty
    Once installed the plugs would only last an hour,some even 15...
  22. Replies
    149
    Views
    29,586

    Must be winter time in the US of A as the BS...

    Must be winter time in the US of A as the BS threads come out again........
  23. Replies
    4
    Views
    725

    Di"s run 3 times the amount of water through the...

    Di"s run 3 times the amount of water through the cooling system than carb models to keep the magneto from getting to hot as it runs alot of electronics,pumps etc. The engine wont be running at lake...
  24. Replies
    13
    Views
    1,341

    If the cooling system self drains you will be...

    If the cooling system self drains you will be fine.When starting always warm the engine up before going flat stick and when finished lower the ski on a trailer with the pump down so all the water...
  25. Replies
    41
    Views
    3,144

    You obviously dont know how a 2 stroke exhaust...

    You obviously dont know how a 2 stroke exhaust wave returns back to the combustion chamber to give a greater effect on the power stroke of the engine
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4