Search

Type: Posts; User: bspanovic

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    193

    I would inspect both the emm male and the...

    I would inspect both the emm male and the connector female ends of the stator connector. It is damaged and the moisture may have entered inside causing corrosion
  2. Replies
    5
    Views
    153

    Welcome to GH! The ground point on your engine...

    Welcome to GH!

    The ground point on your engine is the bolt at the back of your crankcase, PTO end, the exhaust side. it should be clean and bolt fully tightened.
    The connector in the picture is...
  3. Replies
    6
    Views
    119

    I had the same issue when I tried to bypass my...

    I had the same issue when I tried to bypass my faulty Genesis MFD. Shorting 1 and 3 pins would not make the engine crank. I sourced a Virage MFD and still using it
  4. Replies
    6
    Views
    119

    Very likely, a bad MFI of MFD can cause strange...

    Very likely, a bad MFI of MFD can cause strange things including no start. Virage's MFI will work on Genesis and start the engine but without the extra display features
  5. Replies
    13
    Views
    345

    I make sure my fuel in never more than two months...

    I make sure my fuel in never more than two months old. Even so few times I've had problems with the "fresh" fuel. Ficht engines are sensitive on bad fuel. I always use the highest octane fuel (98...
  6. Replies
    6
    Views
    131

    Interesting symptoms. Do you have a spare MFD or...

    Interesting symptoms. Do you have a spare MFD or speedometer to try out?
  7. If your MSX EMM is working I would get the TXi's...

    If your MSX EMM is working I would get the TXi's injectors mapped to it or simply swap the injectors too and just run the TXi engine ..
  8. Sticky: Great. 3.8A pump current draw under the load is...

    Great. 3.8A pump current draw under the load is something we are looking for.
  9. Replies
    1
    Views
    81

    Oil Lines Replacement

    Looking to retire the OEM oil lines used on Ficht engines and not very sure what to replaced it with. I can find some Silicone tubing in the right size 1/8'' or 3mm X 7mm but the smallest rubber or...
  10. Thread: firing order

    by bspanovic
    Replies
    4
    Views
    132

    if your coils are mounted on the bracket under...

    if your coils are mounted on the bracket under the seat, check the engraving on the bracket and it will tell you the Firing Order!
  11. Replies
    8
    Views
    183

    Magnet polarity is important as physical...

    Magnet polarity is important as physical positioning is
  12. Replies
    4
    Views
    111

    Most likely your solenoid is about to die. Black...

    Most likely your solenoid is about to die. Black and fully molded solenoid is recommended.
  13. it is the main water intake hose for engine...

    it is the main water intake hose for engine cooling. The idea is to stop the water ingestion into the cooling system and unnecessarily flood the engine... clamp it down somewhere at the back of hull...
  14. Sticky: @12.32 on PS (alternator V is typically above...

    @12.32 on PS (alternator V is typically above +13V) and without the FPR in the photo I get the similar result with my aftermarket pump.
    It would be good if somebody who has purchased and installed...
  15. Sticky: Yeah, my (other) aftermarket pump is about the...

    Yeah, my (other) aftermarket pump is about the same when just connected to PS under no load and no FPR connected. The picture doesn't show the whole rig..
  16. Sticky: Have you had a chance to measure the current on...

    Have you had a chance to measure the current on them or just going by the seller's spec?
  17. Replies
    32
    Views
    1,153

    Don't use water for testing. It will make corrode...

    Don't use water for testing. It will make corrode the internal electrical parts inside the pump.
  18. The southern hemisphere branch of the Lakesite...

    The southern hemisphere branch of the Lakesite Tech?:) BTW, I think the EMM flash memory programing worked well....will PM you the details.
    Cheers
  19. PM me if you think I can help you. I am in...

    PM me if you think I can help you. I am in Sydney.
    Cheers
  20. I don't think any member here would have...

    I don't think any member here would have schematics but I do know that HiPerCo has it all worked out. If you are happy to pay shipping to US and back and convert it all to $ Oz (+ the cost of repair)...
  21. Replies
    28
    Views
    1,063

    ..and those fragile plastic nipples on the top of...

    ..and those fragile plastic nipples on the top of the pump for fuel lines..
  22. I think the manual says to change spark plugs...

    I think the manual says to change spark plugs every 100 hrs but I find that my plugs usually start to play up before that..
  23. Thread: 12 pin mfd

    by bspanovic
    Replies
    1
    Views
    194

    WTB - Parts I have a used and brand new MFI of Virage. PM if...

    I have a used and brand new MFI of Virage. PM if interested.
  24. Replies
    6
    Views
    239

    Check your spark plugs. When out on the water and...

    Check your spark plugs. When out on the water and after some ride feel by hand all three cylinders if they are the same temeperature. You should be able to hold your hand on a cyliner for 5 sec or...
  25. Replies
    6
    Views
    880

    Thanks, I will pass on your comments. Cheers

    Thanks, I will pass on your comments.
    Cheers
Results 1 to 25 of 149
Page 1 of 6 1 2 3 4