Search

Page 1 of 3 1 2 3

Search: Search took 1.00 seconds.

  1. Post a picture of the engine with spark plugs...

    Post a picture of the engine with spark plugs removed.
    The cylinder furthest forward is #1.
  2. Oil smoke has a blue tint. Water in the...

    Oil smoke has a blue tint. Water in the combustion camber will be white.

    Is this happening with the craft in the water ?

    With fuel infection you CAN NOT use premix. Oil will not get down to the...
  3. Replies
    7
    Views
    208

    https://www.watercraftsuperstore.net/?msclkid=1a18...

    https://www.watercraftsuperstore.net/?msclkid=1a18871c792b164e9e06d9cfbfa1aef6&utm_source=bing&utm_medium=cpc&utm_campaign=**LP%20Branded&utm_term=watercraft%20superstore&utm_content=Watercraft%20Supe...
  4. Most of the water cooled the pipe first-then goes...

    Most of the water cooled the pipe first-then goes to exhaust manifold-then into the engine,
    The small hose would let some of the hot water go out. The Polaris engine is self draining through that...
  5. Replies
    18
    Views
    468

    Yes, center carb hose is the return. Yes...

    Yes, center carb hose is the return. Yes -separator-switch hose is supply,goes to front and rear carb, marked 'RES' on sender.
    Yes the sending unit itself has small letters molded into the...
  6. Replies
    6
    Views
    162

    Looks like at some point the 2002 model is listed...

    Looks like at some point the 2002 model is listed as having the "high start" CDI and flywheel. As far as I know there is no CDI available for high start. I think that was also later 02 models and all...
  7. Replies
    22
    Views
    1,324

    The bracket will go on the inside of the hull....

    The bracket will go on the inside of the hull. The jet pump is already a large chunk of metal. So you will pretty much sandwich the hull between metal. Spread the load over a large area of hull...
  8. Replies
    1
    Views
    105

    The 3/4 hose could be routed as needed or get 90...

    The 3/4 hose could be routed as needed or get 90 degree elbows from a hardware store.

    The exhaust hose if I remember correctly is 2 3/4,possibly 2 7/8. I have used silicone 90 degree elbows that...
  9. Replies
    15
    Views
    501

    The black wire at the 12 pin connecter for MFI.

    The black wire at the 12 pin connecter for MFI.
  10. http://parts.polarisind.com/Browse/Browse.asp ...

    http://parts.polarisind.com/Browse/Browse.asp

    5410663
    BUMPER,DRIVE SHAFT
    ...
  11. Replies
    2
    Views
    886

    The nice thing about that cover is it will work...

    The nice thing about that cover is it will work with the factory heads and also could use the Hotseat performance heads.
  12. Replies
    7
    Views
    503

    Welcome to GreenHulk .

    Welcome to GreenHulk .
  13. Replies
    5
    Views
    367

    Also plug wires and boots.

    Also plug wires and boots.
  14. Replies
    1
    Views
    116

    The arm height is measured by placing a straight...

    The arm height is measured by placing a straight edge on the surface of the carb above the arm. Measure .060 inch from straight edge down to button on arm.
    Pop off is 18-20 psi.
  15. Replies
    4
    Views
    355

    Welcome to Green Hulk. For 2 years Polaris used...

    Welcome to Green Hulk.
    For 2 years Polaris used what they call "high start" CDI and flywheel.
    You are lucky enough to have one. You have 2 options- buy used CDI or use a regular CDI that SBT sells...
  16. Replies
    12
    Views
    594

    I have been talking with "xtxracer" he is also a...

    I have been talking with "xtxracer" he is also a member here. He sold some new factory parts a while back,most notably complete Virage seat assemblies. He has LR505's for sale,he might have access to...
  17. Replies
    15
    Views
    745

    Where the red/pur CDI wire attaches should be the...

    Where the red/pur CDI wire attaches should be the ONLY difference in the factory wiring manual.
    There was a TSB to change that.

    Put it back and test for power on the orange or replace the LR.
  18. Those spark plug wires are the type used with the...

    Those spark plug wires are the type used with the update ignition coil- which means it should have the updated ignition.

    The picture showing the front of the engine shows the oil pump block off...
  19. Replies
    68
    Views
    9,649

    When K447 replies to your post, all there is to...

    When K447 replies to your post, all there is to say is "Thank you". No need for a +
  20. Replies
    11
    Views
    2,153

    The SLX should see 6700 and depending on rider...

    The SLX should see 6700 and depending on rider weight, like 63-65 mph.
    I would try it in the SLTX,that would be the only way to say for sure. And of course, if you like it.
  21. Replies
    11
    Views
    2,153

    Its actually an easy job with the right tools. ...

    Its actually an easy job with the right tools.

    Only the impeller jets replaced.
    After removing the pump stator-remove cone from rear- impeller shaft will be visible-there are 2 flat surfaces,...
  22. Replies
    11
    Views
    2,153

    I use the Nujet 7.0 in my 2001 SLX. It is the...

    I use the Nujet 7.0 in my 2001 SLX. It is the best impeller I tried in it. It deffinetly had the best top speed, by 1 - 1.5 mph , even over the Polaris 7.0 impellers. My SLX also has the R&D 650...
  23. Yes, the second post is correct.

    Yes, the second post is correct.
  24. That's not the typical failure we have seen. As...

    That's not the typical failure we have seen. As things heat up-they expand,that could cause a solder joint to come loose. So it is a possibility.

    The "P" stands for "projector". As in: projects...
  25. Sorry, I should have said "grey" with flat /blade...

    Sorry, I should have said "grey" with flat /blade style connector. I have all sorts of trouble with colors. But being so accustomed to connecting these CDI, I pretty much connect the stator portion...
Results 1 to 25 of 70
Page 1 of 3 1 2 3