Search

Type: Posts; User: Joshbot007

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Needle and seat. I had the bad diaphragms first...

    Needle and seat. I had the bad diaphragms first but changed them out for a legitimate type not the weve. It pumps really well. I checked pop off again and its dead on
  2. Filters were checked and clean. Installed a SBT...

    Filters were checked and clean. Installed a SBT kit last summer but used better needles than the ones that come with the kits.
  3. Had the carbs all apart and they looked clean as...

    Had the carbs all apart and they looked clean as a whistle. All seals including screw orings looked good. This has me confused..... not really sure what to try next. Maybe rejet the center cylinder?...
  4. Ok so motor is back together, timing plate...

    Ok so motor is back together, timing plate removed, and I took to a glass like river to test this weekend and I found this.

    started with the highs out 1 turn, ran super strong but when checked it...
  5. Thanks and will do. Also the engine is already...

    Thanks and will do. Also the engine is already out as that was the only way I could find the leaks
  6. http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=450443&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=450444&stc=1
  7. Ok so the pistons and cylinders looked way better...

    Ok so the pistons and cylinders looked way better then I would of thought. The “scoring” marks are just slightly shiny lines that can’t even be felt by my finger. The cylinders are still...
  8. http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=450429&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=450430&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=450431&s...
  9. Thanks for the replies so far. I pressurized the...

    Thanks for the replies so far. I pressurized the engine and found it is leaking all around the cylinder base where it meets the bottom end at the gasket. I guess I will be ordering new gaskets and...
  10. Reeds were checked with a visual inspection No...

    Reeds were checked with a visual inspection

    No leak down test but I will

    Pull the head off? Not yet but Yes I will do that

    I want to buy stock adjustment screws for two reasons. As a kit...
  11. The plugs were fine and it was running great but...

    The plugs were fine and it was running great but I installed a timing advance plate and aftermarket waterbox and decided to ritchen it up before I even tried it (mistake). Now I am having a hard time...
  12. CDK 2 help for making easy adjustments on 1100 zxi

    Long story short I am having problems tuning my cdk2s on an 96 1100 zxi. It really sucks to have to take off the carbs each time to adjust and the middle main screw sucks *** to adjust. Does anyone...
  13. It is brand new. It just appears that when they...

    It is brand new. It just appears that when they pressed it together that the seals are tight against the inner race of the bearing causing more friction but I wonder if they are supposed to be tight...
  14. How freely Is the bearing in these supposed to...

    How freely Is the bearing in these supposed to spin? I found a killer deal on a wsm one that was the full assembly for the price of the empty wsm so I figured Id try it and if I didnít like it press...
  15. I am located in Hershey PA. I already pulled the...

    I am located in Hershey PA. I already pulled the motor, it didnít take much more then an hour as Im pretty good with working on things
  16. I blocked the oil pump off and bypassed the...

    I blocked the oil pump off and bypassed the lines. I was told that bypassing the coolant lines is fine as per a post I made here about a month ago. Do you agree with that?
  17. Replies
    1
    Views
    113

    No one has any experience with these?? Good or...

    No one has any experience with these?? Good or bad? I wanna pull the trigger and get it asap because I have to replace the stator gasket anyway but I wanna make sure Im not missing any big smoking...
  18. Thanks! I already removed the engine prior to...

    Thanks! I already removed the engine prior to reading this sorry but I wanted to check the motor mounts anyway. I will use the “right stuff”. As for the motor mounts they look good in my hand and...
  19. Ok thanks! As far as the sealant goes Im a bit...

    Ok thanks! As far as the sealant goes Im a bit confused. I heard people say to use epoxy and I can see epoxy from underneath the ski right now, some say use just silicone, and some permatex which i...
  20. Replies
    1
    Views
    113

    1100 zxi timing advance kit/plate

    I have to take my motor out to replace my driveshaft holder,bearings, and seals. While I had it out I figured it would be an opportune time to put on a timing advance plate so I started to do some...
  21. In addition to my last reply, has anyone tried...

    In addition to my last reply, has anyone tried just the aftermarket holder itself? The reason I ask is oem kawasaki holders are $250+ where the aftermarket are sub 100. I would use oem seals and...
  22. Thanks! I will go oem and check the mounts. Im...

    Thanks! I will go oem and check the mounts. Im wondering if I don’t see any problem with the mounts are they good or does the rubber get soft with age and allows more movement?
  23. Sounds good! Does anyone know if the sbt...

    Sounds good! Does anyone know if the sbt preassembled ones are any good or are the bearings and seals junk? Also do the motor mounts in these skis go bad? Wondering if excessive motor mount movement...
  24. 1100 Zxi though drive line plate spinning

    The outer race that the seals and bearings go into is spinning inside the metal plate. Is this normal? I had a problem on my last ride where I seemed to be getting a lot of driveline resistance....
  25. Replies
    0
    Views
    121

    1100 zxi waterbox mod help

    So I got my waterbox out with the hope of modifying it with that whole 1.5in hole saw through the baffle thing. I wasnít really sure how to do it but figured once I got it off It would be pretty self...
Results 1 to 25 of 75
Page 1 of 3 1 2 3