Search

Page 1 of 2 1 2

Search: Search took 1.00 seconds.

  1. Sorry, not going through and re-reading...

    Sorry, not going through and re-reading everything.

    Is the engine mounted to the engine plate securely? The ground wire is bolted to the engine plate, which is bolted to the engine. That is the...
  2. Reminder for everyone doing diagnostics ... never...

    Reminder for everyone doing diagnostics ... never assume there is only one problem, only one thing causing you trouble.

    Often there is more than one problem happening. Sometimes the problems...
  3. This is a common leak. The actual seal for the...

    This is a common leak.

    The actual seal for the water tube is a square shouldered rubber seal that is trapped between the jet pump base and the hull transom. Not possible to access or replace...
  4. Replies
    209
    Views
    20,659

    View Post

    I seem to recall there was a special ‘more hardened’ long driveshaft for the Pro that was intended to help with the shaft whipping when the pump extension was located in front of the impeller/stator....
  5. Replies
    27
    Views
    2,740

    Whatever method you use to block/fill the side...

    Whatever method you use to block/fill the side vent hole in the main pickup tube, be careful to not block or restrict the internal flow up the tube from the bottom.

    The aluminum extrusion is...
  6. Replies
    27
    Views
    2,740

    Pretty sure Casey is right about the SL 700 also...

    Pretty sure Casey is right about the SL 700 also having the correct fuel sender also. I know a 1995 750 works in the PRO as I have done it.

    OK, visualize the silver tube fuel sender.

    As Casey...
  7. Replies
    27
    Views
    2,740

    It's not a reserve tank. The sender simply picks...

    It's not a reserve tank. The sender simply picks up fuel from a different spot,higher up so it runs out of gas with gas still in the tank.Switch to reserve and it picks up the rest of the gas in the...
  8. Replies
    624
    Views
    89,226

    hello i'm restoring two of them here in...

    hello
    i'm restoring two of them here in italy,the first i bought a 99 was good inside with a bad bottom hull,the second a 2000 the opposite good hull bad engine....then recently i found in a...
  9. Replies
    74
    Views
    10,940

    Ski looks awesome and glad to see your all good ...

    Ski looks awesome and glad to see your all good
    Man I have been watching the news , not good
  10. Replies
    74
    Views
    10,940

    Glad your safe.

    Glad your safe.
  11. Replies
    74
    Views
    10,940

    Very nice project review, keep 'em coming!

    Very nice project review, keep 'em coming!
  12. Thread: 785 PROject

    by rpa101
    Replies
    273
    Views
    22,923

    http://www.greenhulk.net/forums/attachment.php?att...

    http://www.greenhulk.net/forums/attachment.php?attachmentid=415165&stc=1My aluminium came in today :pnow let the domes begin lol
  13. Replies
    209
    Views
    20,659

    As far as your hood popping open, you should...

    As far as your hood popping open, you should consider a set of snowmobile hood tiedowns. Even with a properly adjusted latch, you may find that it still wants to pop open.
  14. Thread: 785 PROject

    by rpa101
    Replies
    273
    Views
    22,923

    A GH member let me borrow a dot 1 dome to copy...

    A GH member let me borrow a dot 1 dome to copy for my hot seat head , wishing my lath was cnc lol
  15. Replies
    209
    Views
    20,659

    I can definitely hear the RPM drop like you're...

    I can definitely hear the RPM drop like you're describing. My gut tells me that it's more than just engine load, but I don't know where to tell you to look. It sounds like you've been through every...
  16. Replies
    12
    Views
    1,826

    The bumpers are there to prevent the driveshaft...

    The bumpers are there to prevent the driveshaft from walking up and down the splines as you ride. The rubber provides a little length give if the hull flexes or the engine flexes towards the jet...
  17. Replies
    209
    Views
    20,659

    WSM or SBT are prob made by the same place, just...

    WSM or SBT are prob made by the same place, just put different name on it.

    I wonder if you're sucking a little water into that CEN cyl? Normally if that's the case, the piston is completely clean,...
  18. Replies
    209
    Views
    20,659

    I don't know if I'd say better cable but it...

    I don't know if I'd say better cable but it looked just as similar as the stock one. I replaced my throttle and steering cables with SBT ones I believe and fit fine and work great.
  19. Replies
    209
    Views
    20,659

    I wouldn't lean that MAG out any more. That's a...

    I wouldn't lean that MAG out any more. That's a good/reliable wash unless you want every ounce of performance out of it and don't mind dancing on the edge. The CEN, yes, lean that out.

    As for the...
  20. Replies
    11
    Views
    1,114

    When the leading edge is slightly rounded there...

    When the leading edge is slightly rounded there is less risk of localized turbulence/cavitation if the water flow is not completely aligned with the 'blade' leading edge.

    A really sharp leading...
  21. Replies
    11
    Views
    1,279

    ADA...

    ADA spec.shttp://www.greenhulk.net/forums/attachment.php?attachmentid=408290&stc=1
  22. Thread: Oil

    by Policeman
    Replies
    16
    Views
    1,730

    Freedom04, I own 3 Polaris Virage 700 and have...

    Freedom04, I own 3 Polaris Virage 700 and have had the pleasure of replacing 2 engines. I also purchased the SBT engines with the 2 year no fault warranty and have had great luck with them. You are...
  23. Replies
    14
    Views
    880

    Are the spacer rings magnetic? If not, probably...

    Are the spacer rings magnetic? If not, probably stainless steel.

    Be careful with hand sanding. It is critical that the spacer ends be perfectly square to the long axis. When the impeller is...
  24. Replies
    209
    Views
    20,659

    https://mrtitanium.info/2008/03/17/how-to-tell-if-...

    https://mrtitanium.info/2008/03/17/how-to-tell-if-a-piece-of-metal-is-really-titanium/
  25. Replies
    3
    Views
    755

    I'll be asking for donations to my annual charity...

    I'll be asking for donations to my annual charity ride soon enough. :)

    Summer 2017 Ride for Dad on Big Rideau (donations link not yet available).

    Bookmark this thread (or subscribe, even...
Results 1 to 25 of 30
Page 1 of 2 1 2