Search

Type: Posts; User: Teufelhund

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    211

    Was most likely my last ride of the year, so it...

    Was most likely my last ride of the year, so it won’t be till spring I’m back in sadly:|. I will do full stage 2 over winter and then tune and tweak. It was odd, it really felt like how intake...
  2. Replies
    3
    Views
    211

    Clutch needs warmup?

    So, went for probably last ride of the season. Air temp 53įF, water was in the mid 60s. After being at dock a few minutes I went out to do some part pulls to warm up, waiting on the other guys. ...
  3. Replies
    103
    Views
    9,539

    http://www.makita-groupe.fr/notices/NOTICE_9502332...

    http://www.makita-groupe.fr/notices/NOTICE_950233210.pdf

    lol, a bit easier to read :facepalm:
  4. Replies
    103
    Views
    9,539

    Instructions

    I have mine wrapped on coil 1 only, and set to P:41, works perfectly.
  5. Replies
    103
    Views
    9,539

    yes the wire just loops thru the 2 holes which...

    yes the wire just loops thru the 2 holes which holds it secure then, but is also easily removable.
  6. Replies
    103
    Views
    9,539

    View Post

    So, itís a completely smooth plastic case, the 2 small holes on side are where u run the wire from wrapped coil pack. I also used some clear gorilla tape to seal from to plastic case as itís...
  7. Replies
    103
    Views
    9,539

    Yeah that’s a good price I think I paid $208 for...

    Yeah that’s a good price I think I paid $208 for mine. I used this Velcro (plastic + waterproof) from Lowes, and attached it to the top of my glove box lid.

    3-in x 1-in 2-Pack Clear Fastener...
  8. Replies
    12
    Views
    536

    No, it’s the gp in my signature, we stopped and...

    No, it’s the gp in my signature, we stopped and got fuel at a marina. (Yikes on price!). Yes, it’s the same tank, only 18.5 gallons
  9. Replies
    103
    Views
    9,539

    ONLY place I could find mine was eBay. All...

    ONLY place I could find mine was eBay. All pretty similar at about $210, I tried to find the one with best seller and shortest time combo. It’s about 2-3 weeks shipping, coming from Japan. No one...
  10. Replies
    12
    Views
    536

    Here’s todays data, rode 112 miles on dash (which...

    Here’s todays data, rode 112 miles on dash (which the first stop was within .3 miles of google). Fuel used was 18.5 gal, at a rate of 5.9 mpg on dash. Was riding 45-55 mph for most of cruising, a...
  11. Replies
    23
    Views
    3,876

    Here is a previous thread on this subject, u can...

    Here is a previous thread on this subject, u can see the potential problem areas, but overall I’d think there’s no difference between this and tapping the manifold directly.
    ...
  12. Replies
    103
    Views
    9,539

    Very cool, nice to have that info for my build…u...

    Very cool, nice to have that info for my build…u just elongated the bolt holes to offset to the rear and that was all you needed? Glad to hear 85 mph, I’m hoping to be there +1-2 more. I’ll have to...
  13. I too use the motorcraft fl400s. ...

    I too use the motorcraft fl400s.

    https://www.amazon.com/dp/B000AS3D42/ref=cm_sw_em_r_mt_dp_SEZDB9WMDWWBACNGYKZA?_encoding=UTF8&psc=1

    Here’s an older link with a plethora of cross referenced...
  14. Replies
    103
    Views
    9,539

    Lol, u can seriously drill the hole for the thru...

    Lol, u can seriously drill the hole for the thru fitting with the pump in?? Haha I’m not putting a hole in my hull without like quadruple checking things and that pump gotta be out my way:smt119!
  15. Replies
    103
    Views
    9,539

    Just curious, if you think you don’t need to...

    Just curious, if you think you don’t need to remove the pump, does that mean you are not installing the pro cooling kit? Seems impossible to install without pump out… Ofc you don’t need the pro...
  16. Replies
    12
    Views
    536

    Yeah I haven’t logged total consumption but I...

    Yeah I haven’t logged total consumption but I also was averaging about 5-5.5 mpg from dash computer, I reset before each ride to follow tank to make sure I’m not actually on empty
  17. So I have the same basic mods as tucker…except...

    So I have the same basic mods as tucker…except haven’t done ribbon delete yet. I have gen 2 riva ride plate + intake grate. I never ran my stock ride plate on my stage 1+ so I can’t compare. Using...
  18. Replies
    103
    Views
    9,539

    View Post

    the coupler I refer to is the factory 90į coming off the hull is replaced with a very short straight piece by Worx. The hose then goes from water box to that new “coupler”. The tach I have now is the...
  19. Replies
    103
    Views
    9,539

    I left water box stock, added worx free flow...

    I left water box stock, added worx free flow going out factory hole in hull, only changed the coupler. I didn’t notice much top end speed, perhaps a tiny bit of extra pull…my prop is too tall, I...
  20. Replies
    103
    Views
    9,539

    Just rode tonight after adding a Worx free flow...

    Just rode tonight after adding a Worx free flow exhaust to my setup…gotta say, I’m not a big fan, fairly annoying drone thru 2500-5000 rpm, gotta be going near 45 before it subsides. My first...
  21. There’s a locking lever, you slide it and the...

    There’s a locking lever, you slide it and the socket will start to release
  22. Maptuner

    This one
  23. Lol, of course..that will be my next problem in...

    Lol, of course..that will be my next problem in my journey to stage 2, maptuner won’t work :facepalm:
  24. Replies
    103
    Views
    9,539

    K447, u are absolutely one of the best sources of...

    K447, u are absolutely one of the best sources of info here in the forums, with a wealth of knowledge just overwhelming at times. I agree in principle on what your saying, but the reality of exposed...
  25. Replies
    103
    Views
    9,539

    Dual battery vid

    Hereís a link to my description of my wiringÖlol, keep in mind Iíve no aspirations to be a YouTube star, hence my poor vid skills

    https://youtu.be/2NvalvG7w-A
Results 1 to 25 of 156
Page 1 of 7 1 2 3 4