Search

Page 1 of 16 1 2 3 4

Search: Search took 1.00 seconds.

  1. What about Honda PWC they were turbo?

    What about Honda PWC they were turbo?
  2. Replies
    12
    Views
    696

    on the exhaust mod did you trim about 3 inches...

    on the exhaust mod did you trim about 3 inches off the exhaust hose end that extends down inside the plastic box and remove the rubber flap fingers where the exhaust exits the hull. also you need to...
  3. Replies
    15
    Views
    739

    R&D plates are much faster than a Riva plate on a...

    R&D plates are much faster than a Riva plate on a gpr. Put a post on the forum looking for a used one.
  4. Replies
    15
    Views
    739

    the missing main part is a correct ride plate...

    the missing main part is a correct ride plate angle when done correctly it is worth 4 mph
  5. Sticky: I wanted to bring this topic back up for all the...

    I wanted to bring this topic back up for all the new guys.
  6. Replies
    7
    Views
    379

    I did not need one on my ski, 09 fzr, i just used...

    I did not need one on my ski, 09 fzr, i just used the oem spacer , my prop does sit close to stator but the closer the prop is to the stator the better the pump pressure. Riva even offered a set back...
  7. Replies
    2
    Views
    253

    those lines appear to be casting slag lines and...

    those lines appear to be casting slag lines and not cracks. Take some 250 to 300 grit sand paper and sand the entire grate REAL GOOD by hand and you will see those lines will be gone. If after hand...
  8. Replies
    6
    Views
    437

    since you have unhooked the nozzle and it still...

    since you have unhooked the nozzle and it still steers hard next un hook the cable where it connects to the handlebars, if the handlebars turn freely then the cable is the problem and needs...
  9. Replies
    65
    Views
    4,170

    I hate to re post this but I am trying to help,...

    I hate to re post this but I am trying to help, Remove the injectors and have a injector cleaning/ srevice center flow test them. The age and amount of fuel that has passed through them they need...
  10. Replies
    19
    Views
    1,512

    My suggestion is try my mod first it only cost...

    My suggestion is try my mod first it only cost the $1.89 for the plastic pipe plug. Then if you want more noise you can cut a large hole in your hull and do the rear exhaust. It is hard to patch that...
  11. Replies
    19
    Views
    1,512

    Here is the TJ mod it is a little louder but no...

    Here is the TJ mod it is a little louder but no where as loud as a through hull exhaust and your neighbors will be happy also Tommy Jordan ...
  12. I have experimented with different steering...

    I have experimented with different steering nozzle size. I found that running a steering nozzle 2 mm LARGER than the exit nozzle size works best for me. This larger (2mm) size provided the best...
  13. as the water comes out the back side of the prop...

    as the water comes out the back side of the prop through the stator is has developed swirling motion , the purpose of the veins in the reduction nozzle is to straighten the water exit flow for faster...
  14. Replies
    4
    Views
    522

    look good, no problem, just replace them due to...

    look good, no problem, just replace them due to time use.
  15. Replies
    25
    Views
    6,277

    Mittens, looking forward to the results from a...

    Mittens, looking forward to the results from a back to back test of these two tunes. please try to provide as much information on what each tune is. The more information you can provide will be...
  16. Replies
    36
    Views
    4,124

    The ramps at Kerr Lake are open only the ramps...

    The ramps at Kerr Lake are open only the ramps associated with a camp ground are closed. GO ride there. Day Use and Boat Ramp Areas Currently Open:
    Liberty Hill
    Tailrace Park – Picnic...
  17. Replies
    4
    Views
    509

    Jim's Performance in Fla. or Impros are some more...

    Jim's Performance in Fla. or Impros are some more reliable prop benders.
  18. Glad it worked out for you. This is...

    [/QUOTE]

    Glad it worked out for you. This is why I shared my mod with the forum. Tommy Jordan
  19. Replies
    7
    Views
    571

    use the grease on all connections!

    use the grease on all connections!
  20. Replies
    11
    Views
    898

    some battery came with a 1/2 plastic spacer to go...

    some battery came with a 1/2 plastic spacer to go under the battery . you can get a 1 X 4 peace of plank and cut the size of battery to put in bottom of battery box to make the straps tight also.
  21. Replies
    11
    Views
    948

    down side to your set up is the air entering the...

    down side to your set up is the air entering the intake hose is very hot (coming from inside the crankcase) and contaminated with a oil mist. This very hot air makes the inner cooler work that much...
  22. Thread: YES renewal

    by 2fast4u
    Replies
    9
    Views
    782

    There might be a third party warranty company you...

    There might be a third party warranty company you could buy more warranty for your ski. But I only recommend the OEM factory warranty. I have heard horror storys from folks who purchased third party...
  23. Replies
    56
    Views
    7,694

    Allowing these motors to idle for three to four...

    Allowing these motors to idle for three to four minutes prior to shutting them down is a good idea, especially since all the block/head water drains out after the motor is shut down . I always run my...
  24. Replies
    20
    Views
    2,282

    unless you are a expert tuner and have all the...

    unless you are a expert tuner and have all the gauges/data to make sure your tune is correct I would stay away from the self tune and just use one of there time tested tunes from Riva or Dean. A...
  25. I think the machine work charges were $75.00 It...

    I think the machine work charges were $75.00 It was done to reduce the rotational weight so the clutch rpms would slow down faster when the clutch sprag un locked from the supercharger this helped...
Results 1 to 25 of 400
Page 1 of 16 1 2 3 4