Search

Type: Posts; User: eb87

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    220

    Ages ago I had the exact same problem with that...

    Ages ago I had the exact same problem with that bracket bending. Didn't matter if the bracket was new. The way I solved that was to have a shop weld a small gusset. It was super cheap and permanently...
  2. Replies
    7
    Views
    686

    Have you looked at the MAP/TS sensor on top of...

    Have you looked at the MAP/TS sensor on top of the intake? I helped a friend troubleshoot a similar condition and turned out to be that. Be aware not all models use the same part number.
  3. Replies
    5
    Views
    271

    Disclaimer -been a long time since I worked on...

    Disclaimer -been a long time since I worked on these so this info may be incorrect.

    As I recall the MPEM connector is AMPSEAL which is a TE connectivity product. Take a look at connector part...
  4. Replies
    5
    Views
    271

    Assuming the wiring is the same as 05, the power...

    Assuming the wiring is the same as 05, the power to the gauges is Red/black for positive and black negative. The white/red and white/black are for canbus (data) from the MPEM. rest of the wires are...
  5. Replies
    27
    Views
    1,530

    I'd like to do the same thing you've done. I see...

    I'd like to do the same thing you've done. I see the filter in the GH store, don't see the 90 elbow or adapter for the flame arrestor.
    Can you tell me where it came from?
  6. Replies
    1
    Views
    193

    The older doos came with one small zinc in the...

    The older doos came with one small zinc in the pump and one in the ride plate.
  7. Replies
    1
    Views
    245

    Stainless wear ring needs to be drilled?

    I have the stainless wear ring from the GH store. It doesn't say if needs to be drilled for the 2 small screws that were in the plastic one. Drill to match the holes or leave as is?

    Edit: for the...
  8. Replies
    1
    Views
    201

    Pump rebuild kit in GH store?

    2016 RXT 300- Last time the ski was used the pump was whining while flushing. So decided to make sure there was nothing wrong. After staring at the IBR thing for 2 hours (never have touched one)...
  9. Replies
    20
    Views
    5,216

    I got a re-designed end that eliminates the...

    I got a re-designed end that eliminates the holes, looks to me like the weak area on the part. Feels sturdy but haven't installed it yet.
  10. Replies
    19
    Views
    4,080

    who makes the one way valve?

    who makes the one way valve?
  11. Replies
    3
    Views
    561

    WTB - Parts If interested ...

    If interested

    http://www.greenhulk.net/forums/showthread.php?t=252210
  12. Replies
    4
    Views
    773

    I had the same issue, what I did was heat the...

    I had the same issue, what I did was heat the o-ring to it becomes pliable and it will compress enough. I used a hair drier to not overheat it, went in like butter.
  13. Replies
    8
    Views
    1,008

    The 05 RXT and 06 RXT have different...

    The 05 RXT and 06 RXT have different shafts/bellows/carbon seal, the 05 is smaller diameter than the 06.
  14. Replies
    21
    Views
    2,907

    but the fuse is on the DC side after the...

    but the fuse is on the DC side after the regulator/rectifier. There is no fuse or any other protection from the stator to the regulator/rectifier.
  15. Replies
    21
    Views
    2,907

    Perhaps is the rectifier/voltage regulator...

    Perhaps is the rectifier/voltage regulator pulling excessive power, causing the wire to overheat. The only reason (besides a short or bad wire) that typically causes that.
  16. Replies
    13
    Views
    1,957

    If the stock tune is not able to compensate for a...

    If the stock tune is not able to compensate for a cold air intake, is it also unable to compensate when riding on a cool day?
  17. Replies
    13
    Views
    1,957

    wasn't there a thread stating the stock tune was...

    wasn't there a thread stating the stock tune was able to compensate for a cold air intake?
  18. sharp!

    sharp!
  19. Replies
    20
    Views
    3,909

    FS - Parts I'll take one as well, need the email to send it...

    I'll take one as well, need the email to send it to.
  20. Replies
    7
    Views
    956

    Had a similar issue on my old ski few years ago....

    Had a similar issue on my old ski few years ago. This is what I used. The pin actually comes out the top....meaning you'll have to cut it.
    ...
  21. Thread: Rxt300 IBR issue

    by eb87
    Replies
    21
    Views
    3,026

    Had a similar issue where it would start...

    Had a similar issue where it would start correctly in neutral and go forward but would not go back to neutral or reverse unless the engine was turned off. Turned out to be an issue where the IBR...
  22. Replies
    4
    Views
    746

    It's the coolant hose, top right side of the heat...

    It's the coolant hose, top right side of the heat exchanger. Not the raw water coming from the pump.
  23. Replies
    4
    Views
    746

    300 heat exchanger hose

    The short hose with the 90 degree elbow that was part of the recall going to the heat exchanger on my ski keeps walking. By that I mean every few hours I have to loosen the clamp and push the hose...
  24. Thread: stretch bolts

    by eb87
    Replies
    2
    Views
    378

    WTB - Parts I have a set of head bolts and the 3 cam bolts,...

    I have a set of head bolts and the 3 cam bolts, new.
  25. Thread: Fizzle F1000 kit

    by eb87
    Replies
    2
    Views
    1,666

    FS IC still for sale.

    IC still for sale.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4