Search

Type: Posts; User: 2fast4u

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    18
    Views
    771

    Allowing these motors to idle for three to four...

    Allowing these motors to idle for three to four minutes prior to shutting them down is a good idea, especially since all the block/head water drains out after the motor is shut down . I always run my...
  2. Replies
    7
    Views
    366

    If you think your ecu is bad ask around and see...

    If you think your ecu is bad ask around and see if you can borrow a known good ecu from another ski same model and test it on your ski. Then you will be 100% sure it is the ecu. Just my 2 cent worth...
  3. that looks good, but I use my trim a lot under...

    that looks good, but I use my trim a lot under power and need to leave the trim sleeve on for leverage .
  4. that works good for late model skis but my ski...

    that works good for late model skis but my ski has a manual trim on the left side and the left grip has to be larger to fit over the trim sleeve .
  5. Replies
    20
    Views
    1,409

    unless you are a expert tuner and have all the...

    unless you are a expert tuner and have all the gauges/data to make sure your tune is correct I would stay away from the self tune and just use one of there time tested tunes from Riva or Dean. A...
  6. suggestions for replacement handle bar grips?

    2009 Fzr with stock oem handle bars. Looking for suggestions on replacements grips for my ski. What are you guys using? Thanks for your reply.
  7. Replies
    14
    Views
    690

    it does not matter what pump size you have, the...

    it does not matter what pump size you have, the fuel pressure regulator is what controls the final fuel pressure at the injectors. you need a fuel pressure gauge after the regulator where the fuel...
  8. Replies
    11
    Views
    501

    Your modified Riva SS grate looks to be the best...

    Your modified Riva SS grate looks to be the best for rough water use. If top speed on calm water is what you are lookin for then find a R&D grate there should be 1 to 2 mph difference in these two...
  9. Replies
    11
    Views
    501

    the dean,s grate looks like the two out side...

    the dean,s grate looks like the two out side wings on the center bars of the grate are completely even with the front of the scoop wing, where the stock one the wings do not go down a much as the...
  10. Replies
    11
    Views
    501

    can some post a picture of a un modded Riva...

    can some post a picture of a un modded Riva stainless grate for comparison?
  11. Replies
    11
    Views
    501

    post pictures of grate please.

    post pictures of grate please.
  12. Replies
    9
    Views
    225

    never heard of that. WHY will a agm battery...

    never heard of that. WHY will a agm battery damage that stuff? To high of voltage or that battery requires a higher voltage to keep it charged . ??????????????
  13. yes but the cruse control function will NOT work.

    yes but the cruse control function will NOT work.
  14. Thread: Water in hull

    by 2fast4u
    Replies
    33
    Views
    3,567

    My ski is totally dry inside after a 120 mile...

    My ski is totally dry inside after a 120 mile river ride, no water at all, if there is water in your ski you have a leak unless you take water in around the seat, handle bars or front cowl . 350+...
  15. Replies
    9
    Views
    456

    100% CORRECT this is why these skis are hard to...

    100% CORRECT this is why these skis are hard to start the first time after sitting for months.
  16. Replies
    8
    Views
    411

    replace sparkplugs re test first

    replace sparkplugs re test first
  17. Replies
    42
    Views
    2,343

    I think the machine work charges were $75.00 It...

    I think the machine work charges were $75.00 It was done to reduce the rotational weight so the clutch rpms would slow down faster when the clutch sprag un locked from the supercharger this helped...
  18. Replies
    42
    Views
    2,343

    R&D use to offer this service before they closed...

    R&D use to offer this service before they closed up. I have the weight info before and after machining if I can find it. Here is the in for for you. pictures and weights...
  19. Replies
    42
    Views
    2,343

    unsprung weight usually refers to anything on the...

    unsprung weight usually refers to anything on the car that is Not supported by the suspension . like the wheel, brakes , rear end, lower control arms, ect. sprung weight is anything that the...
  20. Replies
    22
    Views
    2,816

    Looking close at the photo where there thumb is I...

    Looking close at the photo where there thumb is I see heavy cavitation burns on the edge of the prop blades and also some cavitation pitting starting on the blade surface . this is caused by the...
  21. Replies
    16
    Views
    1,378

    when side gaping the sparkplug be care full and...

    when side gaping the sparkplug be care full and do not let the file touch the center electrode only remove material from the ground strap electrode.
  22. Replies
    16
    Views
    1,378

    when you change the original gap on a sparkplug...

    when you change the original gap on a sparkplug say from .038 (out of the box specification) to say .020 (desired plug gap) once the sparkplug has been run and heated and cooled several times the...
  23. Replies
    6
    Views
    498

    small fuel filters in each carb stopped up. R&R...

    small fuel filters in each carb stopped up. R&R carbs.
  24. SOLD Buy the parts from Butterbean 29512, I have had...

    Buy the parts from Butterbean 29512, I have had dealings with him in the past stand up guy for sure. Tommy Jordan
  25. Tell me more on how to mod the ride plate, Thanks

    Tell me more on how to mod the ride plate, Thanks
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4