Search

Type: Posts; User: casey67

Search: Search took 0.01 seconds.

  1. Replies
    62
    Views
    2,737

    Pretty sure none of the 700's used a limiter. If...

    Pretty sure none of the 700's used a limiter.
    If the CDI is in limit mode it would be the grey CDI wire with a flat blade connector.
    If any where, likely on tan terminal at terminal board.
  2. Replies
    62
    Views
    2,737

    You mentioned previous owner being a bit of a...

    You mentioned previous owner being a bit of a cowboy, I guess he "adjusted" the return restrictor.

    Fuel pressure at/around idle should be 1.5 psi. Installing a gauge in the hose running between...
  3. Replies
    62
    Views
    2,737

    The arm that pulls up on the needle part of...

    The arm that pulls up on the needle part of needle/seat.

    IIRC there should be a plastic button on that arm where it contacts the diaphragm.
    Measurement is from that arm/button to the edge of carb...
  4. Replies
    62
    Views
    2,737

    Flat edge across carb body, .060 inch down to...

    Flat edge across carb body, .060 inch down to button on needle arm.

    Blocking off the return will increase the fuel pressure. Enough to keep it running ?

    Did you remove the fuel cap to see if it...
  5. Replies
    62
    Views
    2,737

    It seems just a bit too much, but don't see it as...

    It seems just a bit too much, but don't see it as an issue.

    Have you tested the "pop off" pressure of the needle and seat ?
    Measured and adjusted the needle arm height ?
  6. Replies
    62
    Views
    2,737

    Yes, hoses are correct.

    Yes, hoses are correct.
  7. Replies
    62
    Views
    2,737

    The upper most fitting is the return. It will...

    The upper most fitting is the return. It will have an elbow pressed into the carb body, some twisting and pulling should get that out.
    Working from memory ( a bit strained ) IIRC there will be a...
  8. Replies
    62
    Views
    2,737

    Hang in there, these are pretty much concerns...

    Hang in there, these are pretty much concerns that come with alot of older PWC.

    Keihin has a restrictor molded into the carb outlet, and only the "last carb" or carb body that is used for the...
  9. Replies
    62
    Views
    2,737

    I agree. Water flows into the exhaust pipe first,...

    I agree. Water flows into the exhaust pipe first, then through the exhaust manifold. The restriction is at the water rail/exit. So there will be water pressure present at the EX manifold to cylinder...
  10. Replies
    62
    Views
    2,737

    Sorry to hear of your continued issues. ...

    Sorry to hear of your continued issues.

    Well... at small load/clamping force- a bolt is a bolt.
    Because of the water, PWC bolts are stainless steel. I would make sure they are all stainless....
  11. Replies
    62
    Views
    2,737

    It looks like there are 2 jets installed on that...

    It looks like there are 2 jets installed on that jet block. Is there a jet in the opening on the top right ?

    99SLH should have the 2 jet version carbs (one small on front, one large on rear of jet...
  12. Replies
    62
    Views
    2,737

    Correct, there should be an o-ring style gasket...

    Correct, there should be an o-ring style gasket that fits into that grove.

    The single carb is identical as far as fuel pump, as to the carb you are working on.Your other carb doesnt have a fuel...
Results 1 to 12 of 12