Search

Type: Posts; User: martincom

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Mr. GP1800 makes a good point. If you have a...

    Mr. GP1800 makes a good point. If you have a spark plug that is intermittent, that would cause the surging, change of RPM and hesitation you complain of. From your previous posts, I had assumed...
  2. Replies
    6
    Views
    860

    The MPI 315-0146 is what I utilize and I've had...

    The MPI 315-0146 is what I utilize and I've had good results. Warm the hose, with a heat gun, and grease the barb to slide it over the 5/16" hose barbs.

    You'll also want to utilize Oetiker ...
  3. SBT (https://www.shopsbt.com/) offers re-built...

    SBT offers re-built cranks. Probably others, but that is what comes to mind.
  4. It is time to perform the compression test...

    It is time to perform the compression test queried in post #2.
  5. Replies
    102
    Views
    2,523

    They are all tied together at splice points. ...

    They are all tied together at splice points. When measuring DC voltages, was that with the engine cranking? If so they are low. They should be approximately 21 vdc. That would confirm your new...
  6. The clamps are Oetiker. You can find them in...

    The clamps are Oetiker. You can find them in small quantities on Amazon. You'll probably want to start on McMaster-Carr's web site. They have an excellent chart that denotes the size range, part...
  7. Replies
    102
    Views
    2,523

    No, it feeds power to injectors and also appears...

    No, it feeds power to injectors and also appears in the 4-pin diagnostic software connector.
  8. Mesh filter replacement, courtesy of bfarnam: ...

    Mesh filter replacement, courtesy of bfarnam:

    http://greenhulk.net/forums/showthread.php?t=288609
  9. Be sure to reinforce the fuel pressure regulator,...

    Be sure to reinforce the fuel pressure regulator, utilizing the hose barb method, whether it is still in place or not. It is not if it will fall out, but when.

    Another member had posted a...
  10. I'm B,B,B,B,Blue with envy! Mine are out of the...

    I'm B,B,B,B,Blue with envy! Mine are out of the water, winterized and in storage for the winter. Lifts came out on Labor Day weekend.

    We only stay here for the low taxes.....
  11. #1 Often, they will start and idle when the...

    #1

    Often, they will start and idle when the fuel pressure regulator (FPR) has fallen off---no fuel pressure. The injectors will pump some fuel on their own. Your reported symptoms are typical of...
  12. Replies
    102
    Views
    2,523

    Good to know. Even old dogs learn new tricks.

    Good to know. Even old dogs learn new tricks.
  13. Replies
    102
    Views
    2,523

    Your AC voltage is low on the 2 & 11 section. It...

    Your AC voltage is low on the 2 & 11 section. It should be 7.0 volts. That being said, that section is for the 12 volt output. So that should have nothing to do with your no start, no spark, no...
  14. Replies
    102
    Views
    2,523

    Is it the same, damaged, flywheel?

    Is it the same, damaged, flywheel?
  15. Replies
    102
    Views
    2,523

    Is this the same stator you started with or did...

    Is this the same stator you started with or did you replace it?
  16. Replies
    102
    Views
    2,523

    No.

    No.
  17. Oh yes! Never ending. Folks often ask me how...

    Oh yes! Never ending. Folks often ask me how the fishing is. To which I reply, "I wouldn't have a clue. I live on a lake. Therefore, I don't have time to fish."

    I still have the dock to...
  18. I hope they're on the trailer. With overnight...

    I hope they're on the trailer. With overnight lows in the 40s and even 30s, the water temp has plummeted. All mine came out of the lake Labor Day weekend. The lifts came out on Sunday afternoon. ...
  19. I'll save you a bit of working in the "blind". ...

    I'll save you a bit of working in the "blind". The 40 Pin connector retaining screw requires a 4mm hex (Allen) wrench.
  20. You may want to swap the strong spark coil...

    You may want to swap the strong spark coil primary wire (from EMM) to the other coils and see if the spark remains poor or improves. That should provide an indication whether the coil is the issue...
  21. Replies
    8
    Views
    162

    Sorry, ebay pulled the listing I purchased them...

    Sorry, ebay pulled the listing I purchased them from. The seller has since revised/replaced the listing:
    ...
  22. Replies
    8
    Views
    162

    I don't have a lot of extra shims and depending...

    I don't have a lot of extra shims and depending on your hull, you could need a dozen or more. There are two outfits here in MN that are in the PWC salvage business. PELICAN RAPIDS POWERSPORTS and...
  23. Are the ground wires in place for the coil packs?

    Are the ground wires in place for the coil packs?
  24. Replies
    12
    Views
    312

    Your next step would be to check for 21 vdc on...

    Your next step would be to check for 21 vdc on the white/red wire (21/45 vdc power supply) that feeds power to the injectors. Make this measurement while cranking with a fully charged battery. You...
  25. Replies
    31
    Views
    627

    As you have seen, it does not take much to plug...

    As you have seen, it does not take much to plug the pump intake screen. I pump the tank dry as much as possible. Next, I mop out the rest with paper towels. I let it dry, then wipe out the inside...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4