Search

Page 1 of 16 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    3
    Views
    163

    I take the filter out and crank it in drown mode...

    I take the filter out and crank it in drown mode until oil starts coming up, only takes a few seconds.

    Your assembly lube is what gets it through the first few seconds.
  2. Replies
    7
    Views
    424

    Very cool, can't wait to see the all new RXP,...

    Very cool, can't wait to see the all new RXP, crossing fingers its badass.
  3. Thread: 161mm wear ring

    by ptscon
    Replies
    12
    Views
    379

    A piece of lumber and a hammer.

    A piece of lumber and a hammer.
  4. That skat impeller must be really low pitch for...

    That skat impeller must be really low pitch for you to be able to spin it up that high with only a et135 charger.

    Add pitch and you'll reduce RPM but gain speed. Might need a different impeller,...
  5. Replies
    9
    Views
    446

    Cam will add some nice rumble if you have rear...

    Cam will add some nice rumble if you have rear exhaust :)
  6. Replies
    9
    Views
    231

    2008 had all 3 versions :)

    2008 had all 3 versions :)
  7. Replies
    5
    Views
    219

    The 160 thermostat just gives you a bit more run...

    The 160 thermostat just gives you a bit more run up room since it will cool down to lower temperature. It does not lower the temperature at speed.
  8. And with that you went from simply removing PTO...

    And with that you went from simply removing PTO to stripping the motor for complete cleanup.
  9. Replies
    122
    Views
    6,913

    I'm not sure which parts of this are supposed to...

    I'm not sure which parts of this are supposed to be jokes and which are serious. :-s:D I hope no one was referring to paddle wheel models in this thread.

    Silly to complain about the cluster being...
  10. Thread: Timing question

    by ptscon
    Replies
    1
    Views
    139

    As long as the crank/balancer gear marks mesh...

    As long as the crank/balancer gear marks mesh together in the same spot during rotation you're good.
  11. Replies
    122
    Views
    6,913

    Your RPM is where it should so whatever it is...

    Your RPM is where it should so whatever it is it's not engine related.

    Check your pump seal, wear ring and impeller.
  12. Replies
    9
    Views
    341

    What's the issue exactly? You posted instructions...

    What's the issue exactly? You posted instructions page that says exactly what connects to what.

    Gauge white connects to controller yellow. Note that LC2 has two configurable outputs, those are the...
  13. Replies
    53
    Views
    4,360

    Where are all these failures being reported? Not...

    Where are all these failures being reported? Not seeing this on GH.
  14. Replies
    20
    Views
    1,549

    What the heck? You should be able to do 300...

    What the heck? You should be able to do 300 hours on one seal.
  15. Replies
    12
    Views
    569

    Try it and see how it goes, every ski is a little...

    Try it and see how it goes, every ski is a little different. I'd be surprised if you hit real 75mph with that RPM limit but you get a bit of a bump from your ski being RXT not RXP, so mayyybe. 15/20...
  16. Replies
    12
    Views
    275

    Yes, why add anything that makes it easier for it...

    Yes, why add anything that makes it easier for it to come undone. 4-foot breaker bar later on and problem solved.
  17. Replies
    15
    Views
    458

    This is wrong! DO NOT FOLLOW ANY TORQUE SPECS...

    This is wrong! DO NOT FOLLOW ANY TORQUE SPECS FROM THIS POST!

    Everything around the pump shoe is plastic, if you follow traditional torque specs based on bolt size you will rip things out.

    17...
  18. Replies
    21
    Views
    565

    Look in between the folds of the filter, it's...

    Look in between the folds of the filter, it's normal to find a few small flakes, from gears, as long as they're magnetic it's ok. If they are not magnetic it means aluminum and that's a bad thing.
  19. Replies
    21
    Views
    565

    Not good, hopefully thrust bearing didn't get...

    Not good, hopefully thrust bearing didn't get owned.

    You didn't notice it was loose when you had the pump out to correct the impeller cone? Things didn't look right from your picture in your other...
  20. Replies
    16
    Views
    733

    Is the engine vibrating while running on the hose?

    Is the engine vibrating while running on the hose?
  21. Replies
    16
    Views
    733

    You're 100% sure there's nothing stuck to the...

    You're 100% sure there's nothing stuck to the impeller? All it takes is a finger nail size stick to be stuck to impeller blade to cause what you're describing.
  22. OK, economy will recover after you're gone so no...

    OK, economy will recover after you're gone so no big deal. Are you taking down your family members as well?
  23. Replies
    20
    Views
    810

    I already tried with Link, even submitted a...

    I already tried with Link, even submitted a ticket but it won't happen. Their G4+ line of ECUs, what current Vipec is, is at end of life and no new featuers will be added. Their new G4x lineup...
  24. Replies
    27
    Views
    1,205

    You're putting electric fans to push air into the...

    You're putting electric fans to push air into the hull? It won't work, it's better to simply add openings in the hull than doing fans, the fan will actually be a restriction.

    Take off the charger...
  25. Replies
    20
    Views
    810

    You can read up a bit on this here...

    You can read up a bit on this here http://forums.linkecu.com/topic/6500-trigger-issue-rotax-4-tec/
Results 1 to 25 of 400
Page 1 of 16 1 2 3 4