Search

Type: Posts; User: TJS0712F

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Mcmaster dot com has the same strainer as well.

    Mcmaster dot com has the same strainer as well.
  2. Replies
    19
    Views
    3,756

    Never drilled out a broken fastener in 20 years....

    Never drilled out a broken fastener in 20 years. See post. I just removed a broken shoe bolt from a Yamaha. Plus you might want to start a new thread at this one is 13 years old....
  3. Replies
    5
    Views
    164

    Agree with Steve45. There are bubbles around that...

    Agree with Steve45. There are bubbles around that hole. Looks like it will need a patch. Cut out the corrosion and make a patch and tig it up. Simple. I have done this before as well.
  4. Inducers have been on real jet boats for over 30...

    Inducers have been on real jet boats for over 30 years. Helps in loading the pump.
  5. Replies
    4
    Views
    84

    Nice to get you by. I am not a fan of 5200. Not...

    Nice to get you by. I am not a fan of 5200. Not sure why you did not tap the good one on the right. 1/2" NPT might have worked. I would have done it a little different. TIG build up on the broken one...
  6. Replies
    7
    Views
    208

    Oh and a 110v welder aint gonna cut it.

    Oh and a 110v welder aint gonna cut it.
  7. Replies
    7
    Views
    208

    Never attempt to drill broken fasteners out. It...

    Never attempt to drill broken fasteners out. It only makes matters worse. I usually mig or tig weld a tip and build up on the broken fastener. Then put a nut on the tip and hammer the heat and weld...
  8. Replies
    12
    Views
    235

    Yup. It helped for me.

    Yup. It helped for me.
  9. Replies
    3
    Views
    210

    So what was the no spark cause.

    So what was the no spark cause.
  10. Replies
    12
    Views
    235

    Put a pump wedge in it and get the bow up a...

    Put a pump wedge in it and get the bow up a little. Try that first. I have two wedges in mine.
  11. I have welded one of these blocks together. There...

    I have welded one of these blocks together. There is a post here somewhere. What you need to look at if the crank seal is bad it will suck air and cause a lean condition. Happened to my buddies...
  12. Replies
    12
    Views
    369

    I take my pump apart 2 times a year since my...

    I take my pump apart 2 times a year since my issue. The problem is shaft seals let water into the housing and gets water in the bearing and then it makes a mess. I have a complete re-build and...
  13. Replies
    12
    Views
    369

    Cato3, Reason for this if there is a bearing...

    Cato3,
    Reason for this if there is a bearing failure the shaft walks forward and ruins the engine. Double vane set ups have this set up I think after 2013 or something. The nut on the back of the...
  14. Replies
    2
    Views
    139

    Heat is your friend with stubbon items you are...

    Heat is your friend with stubbon items you are facing. A MAP gas torch will work in this situation if you don't have Oxy/Cet set up.
  15. Replies
    11
    Views
    957

    Fuel socks ...

    Fuel socks

    https://www.highflowfuel.com/i-23908445-quantum-fuel-pump-strainers-qty-3-for-kawasaki-jet-ski-ultra-310-jt1500-efi-2014-2020-replaces-49040-0748.html
  16. Replies
    14
    Views
    3,168

    My ski is ready but my "new" boat is not. I got a...

    My ski is ready but my "new" boat is not. I got a Ski Ray in the winter and have it apart. I should be together soon. We usually hang out at Seaside park (yes Bridgeport folks). Don't knock it till...
  17. Gauge in slo mode. Check ebay for a guage set up....

    Gauge in slo mode. Check ebay for a guage set up. They are not cheap. I think new they are the cost of the machine you are looking at. Kawi's fopar.
  18. Toast. Looks like Jaws at part of it for...

    Toast. Looks like Jaws at part of it for breakfast.
  19. Post some better pics of the issue. Is the whole...

    Post some better pics of the issue. Is the whole part corroded. What is your location. I can fix it for you if you want. See my other tig welding posts.
  20. Replies
    4
    Views
    297

    Poll: It needs to be measured and a pro engine machine...

    It needs to be measured and a pro engine machine shop would be able to tell you if polishing (not ground) will be within spec. There are a few other variables here as well. Hard to tell if it is...
  21. Replies
    7
    Views
    286

    Going to the new three bearing set up requires a...

    Going to the new three bearing set up requires a new pump housing assembly(+2011 up), shaft, retaining nut, and cone set up as well as the bearings and seals that go with it. There are several posts...
  22. Replies
    51
    Views
    2,530

    For the gauge issue. This is normal junk kawi...

    For the gauge issue. This is normal junk kawi gauge. This is a huge issue. Stock replacements fail too. They allow water intrusion. Smokeyseven has a post on this. People say to ground the...
  23. Replies
    5
    Views
    547

    You can cut out the old wear ring, buy on from a...

    You can cut out the old wear ring, buy on from a company in in fla for 70 bucks on ebay. I have a whole write up on this I did years ago on here. Not that hard.
    ...
  24. 07 12F

    07 12F
  25. 40 Hrs. Puked bearings almost trashed my housing...

    40 Hrs. Puked bearings almost trashed my housing (saved it). Total garbage design in all aspects. I have several posts on this.
    T.J.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4