Search

Type: Posts; User: steve45

Page 1 of 8 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    12
    Views
    337

    I don't know. I was never able to find any...

    I don't know. I was never able to find any blockage. My guess would be something like a small stick that dried out, shrank, and came loose.

    I did blow gently back through the pisser (by mouth)...
  2. Replies
    12
    Views
    337

    Took the 'Skis out on our lake today, they...

    Took the 'Skis out on our lake today, they performed perfectly.

    Do these things have a thermostat?
  3. Replies
    4
    Views
    203

    OK, I'm confused. What is a 'flat bottom Ultra...

    OK, I'm confused. What is a 'flat bottom Ultra 150'? And since 2005 was the last year for the 150, are you asking about the 250?
  4. Replies
    10
    Views
    301

    The Kawasaki and Yamaha engines use outside water...

    The Kawasaki and Yamaha engines use outside water from the jet propulsion pump. Open loop.

    Some of the SeaDoos have a closed loop system with a heat exchanger on the bottom of the hull. These...
  5. Does the gas gauge work? If so, you don't need a...

    Does the gas gauge work? If so, you don't need a Reserve setting or a selector valve. Plug the On outlet, hook the hose directly to the Reserve outlet. When the gauge gets low, put gas in it.
    ...
  6. Replies
    23
    Views
    545

    I'd bet that the non-linear ranging is a holdover...

    I'd bet that the non-linear ranging is a holdover from the old style gauges that used a single float on a wire arm and a rheostat. That would give a sinusoidal response.
  7. Replies
    23
    Views
    545

    Think I would have left well enough alone! :lol:

    Think I would have left well enough alone! :lol:
  8. Replies
    23
    Views
    545

    Is it water resistant?

    Is it water resistant?
  9. Thread: New 160 lx

    by steve45
    Replies
    24
    Views
    1,913

    I love your signature, Kev273! Kinda says it...

    I love your signature, Kev273!

    Kinda says it all...
  10. Replies
    10
    Views
    301

    I don't think machining would be much of a...

    I don't think machining would be much of a problem. The crankshaft is threaded. These engines turn CCW when viewed from the rear.

    Sounds like a fun project!
  11. I run 25:1 for break-in. If you're running oil...

    I run 25:1 for break-in. If you're running oil injection, then you want to mix 50:1 in the tank, too.

    Running on the hose doesn't do anything for your break-in procedure.
  12. Try gently heating them to loosen any Loctite...

    Try gently heating them to loosen any Loctite that might be on them.
  13. I would inspect the nipple carefully (I ALWAYS...

    I would inspect the nipple carefully (I ALWAYS look carefully at nipples :lol:). See if it could be leaking where it goes into the casting, or if it has a crack or burr.
  14. Welcome aboard, Colegobin! Do you need a hull?...

    Welcome aboard, Colegobin!

    Do you need a hull? I should have one available in a couple of months. I'm in Texas.
  15. Replies
    12
    Views
    337

    Too nasty to ride on Saturday, as well. 25-30...

    Too nasty to ride on Saturday, as well. 25-30 knot winds, 3 foot waves, sea grass everywhere. Vacation is over, drove home today. I plan to take them to the lake next weekend and run them in fresh...
  16. Glad you found the problem! Do you have the...

    Glad you found the problem! Do you have the right size hose? What brand of hose is it?

    I don't like worm gear clamps, use Oetiker clamps in that application.
  17. Replies
    12
    Views
    337

    I'll have to give that a try, Blake. We did...

    I'll have to give that a try, Blake. We did anchor the 'Skis yesterday and the tide went down, causing them to drag on the sand. I don't have an air compressor with me this week, so I'll see if I...
  18. Not really. Look for one that doesn't have any...

    Not really. Look for one that doesn't have any wear marks in it.
  19. I had to change plugs in one of my 'Skis this...

    I had to change plugs in one of my 'Skis this week and the only kind of lubricant I had with me was Teflon pipe sealant. Smeared a thin layer over the outside of the wire insulators and it works...
  20. Replies
    12
    Views
    337

    Flushed well after each outing. It started...

    Flushed well after each outing.

    It started working normally today after removing the reed valve in the exhaust, but started acting up this afternoon. Ran good, but when we got close to port and...
  21. You might be able to get it re-sleeved. The...

    You might be able to get it re-sleeved. The Kawasaki housings are not intended to be repaired (unlike some other brands), but there are people that do it. SBT does a lot of pump repair, so you...
  22. Replies
    12
    Views
    337

    Thanks, guys! I had another thought last night. ...

    Thanks, guys! I had another thought last night.

    After reading the thread about hydrolocking the Ultra LX engines and the changes to the exhaust system that may have contributed to it, I...
  23. Replies
    12
    Views
    337

    Need Help With Overheating Ultra LX

    Had trouble earlier this week with an Ultra LX (NA engine) running fine at cruising speed, but it would overheat when we got to a no wake zone. Found sea grass once, but it happened several times. ...
  24. Replies
    38
    Views
    4,805

    Those look pretty cool!

    Those look pretty cool!
  25. Welcome aboard, ronrymanr1! Sounds like you...

    Welcome aboard, ronrymanr1!

    Sounds like you have corrosion in the pump housing, which forces the liner inward, causing it to rub on the impeller. All too common, really. You'll most likely have...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4