Search

Search: Search took 1.00 seconds.

  1. Replies
    26
    Views
    2,162

    Yay!

    Yay!
  2. Replies
    26
    Views
    2,162

    I could see the missing grommets causing a vacuum...

    I could see the missing grommets causing a vacuum leak that would possibly make it idle wierd. They always die a time or two after being put back together until the fuel system is primed and the...
  3. Replies
    26
    Views
    2,162

    Looking closely at the pistons, the rear piston...

    Looking closely at the pistons, the rear piston does NOT have the carbon nor the brownish burnt fuel residue that the others do. I really feel like you could have been losing just a tiny bit of...
  4. Replies
    26
    Views
    2,162

    Were you losing coolant? Bad head gasket...

    Were you losing coolant?

    Bad head gasket usually causes coolant to be shot out the overflow bottle at high rpm.

    Coolant passages are all painted black, the flakes you see could be just paint...
  5. Replies
    26
    Views
    2,162

    I really don't see anything with that gasket that...

    I really don't see anything with that gasket that is a 'smoking gun'. It DOES look like the rear cylinder was hot though. Check that head for warpage. I put the head on and torqued, cam and rockers...
  6. Replies
    26
    Views
    2,162

    No, I assumed you had everything apart. It's...

    No, I assumed you had everything apart.

    It's easier to install the gear and plastic cover with the cam loose since you can push the cam back a little giving you more room, especially for the...
  7. Replies
    26
    Views
    2,162

    The only reason a head has to come off is if...

    The only reason a head has to come off is if you're changing the gasket, taking pistons out or doing something to the head itself like guides or seats.

    - remove chain tensioner (should be already...
  8. Replies
    26
    Views
    2,162

    Yes head needs to be installed. You really...

    Yes head needs to be installed. You really should be going by service manual if this is your first time doing it.
  9. Replies
    26
    Views
    2,162

    Whats going on in the middle cylinder? Is that a...

    Whats going on in the middle cylinder? Is that a gap to the left of the piston or just a camera reflection (I hope its a reflection).

    Edit, I see, its just liquid sitting on the piston. Never...
  10. Replies
    26
    Views
    2,162

    Well, the rear cylinder does look like the carbon...

    Well, the rear cylinder does look like the carbon is getting washed off. Post pics of both sides of the head gasket itself. If it's bad you can see where it was leaking.
  11. Replies
    26
    Views
    2,162

    Just curious but could you take off some of pump...

    Just curious but could you take off some of pump housing and using a breaker and I believe a 30 or 32mm socket on the impeller nut work?
    Oopppsss did not read the prior suggestions sorry guys.
  12. Replies
    26
    Views
    2,162

    You don't really have to go through the hustle of...

    You don't really have to go through the hustle of locking the crank, it's a bit of a pain getting to it. As long as your cam is locked and #3 at TDC when you tighten the cam bolts. This actually...
  13. Replies
    26
    Views
    2,162

    I wedge a prybar between 2 of the cam sprocket...

    I wedge a prybar between 2 of the cam sprocket bolts. That gives a 'lever' to spin it.
  14. Replies
    12
    Views
    1,242

    I usually wouldn’t do this I would say ready my...

    I usually wouldn’t do this I would say ready my thread but here is the tsb for the bolts..

    http://greenhulk.net/forums/attachment.php?attachmentid=446452&d=1554007102
  15. Replies
    12
    Views
    1,242

    You should not remove these from the pump UNLESS...

    You should not remove these from the pump UNLESS specifically needed, the manual states this clearly ;) And yes, as mentioned... Change to the upgraded bolts... There was a bulletin out on that... ...
  16. Replies
    12
    Views
    1,242

    The shaft is corroded, but not in the areas that...

    The shaft is corroded, but not in the areas that will affect anything. The tophat will be difficut to remove whenever you have to pull the shaft out.
  17. Replies
    12
    Views
    1,242

    Change your bolts out to the upgraded hex ones ....

    Change your bolts out to the upgraded hex ones . Blue locktight and let sit for a day. Google the 2010 ride plate tsb.

    also that driveshaft is pretty corroded check the carbon seal and drive line...
  18. Replies
    12
    Views
    1,242

    I was a little surprised that they worked on an...

    I was a little surprised that they worked on an Allen head bolt. I thought those were made for hex head bolts? I may have to get a set.
  19. Replies
    12
    Views
    1,242

    You're very welcome, those bolt extractors really...

    You're very welcome, those bolt extractors really come in handy in a tight situation like that, i would definitely replace the allen head bolts with stainless hex head bolts, the updated bolts that...
  20. Replies
    12
    Views
    1,242

    There are special sockets that will bite into the...

    There are special sockets that will bite into the head of the stripped bolt, I use ones like these very often in the automotive world
    ...
Results 1 to 20 of 20