Search

Type: Posts; User: xlint89

Page 1 of 8 1 2 3 4

Search: Search took 0.12 seconds.

  1. Welcome to the Hulk. Runaway engines are...

    Welcome to the Hulk.

    Runaway engines are normally running lean on fuel. When the kill switch doesn't work, it's actually dieseling from a hot spot in the combustion chamber.

    I'd suggest doing a...
  2. Anything is possible, but I highly doubt your...

    Anything is possible, but I highly doubt your carbs are dumping more fuel than the pump can deliver.

    If you have the Mikuni pentagon shaped fuel pump, it delivers 65L per hour. It would not be out...
  3. Replies
    38
    Views
    1,011

    If this guy is parting one out, might look into...

    If this guy is parting one out, might look into the expansion pipe.

    http://greenhulk.net/forums/showthread.php?t=280342
  4. Replies
    38
    Views
    1,011

    Well, that is a bummer. I am fresh out of ideas. ...

    Well, that is a bummer. I am fresh out of ideas.

    Anyone else got any suggestions for this guy?????
  5. Replies
    1
    Views
    94

    Positioned so "up" is correct, and the "sharks...

    Positioned so "up" is correct, and the "sharks fin" on the gasket is situated under the water rail.

    Both pictures you show are positioned correct.
  6. Buna N and Viton seem to be what showed up in my...

    Buna N and Viton seem to be what showed up in my search for fuel related O ring material.

    Not sure why you were fine, then lost fuel level in the separator again. Easy test would be to install a...
  7. I doubt it's the reeds also. But, with them...

    I doubt it's the reeds also. But, with them suggesting the reeds were "iffy" on the PTO, and that cylinder operating the fuel pump, I think that needs to be removed from the list of possibilities...
  8. Replies
    38
    Views
    1,011

    In your picture, what is that black stuff on the...

    In your picture, what is that black stuff on the left?

    If that's an oily goo that seeped under the gasket, that might be the problem. If it is seeping under the gasket, once you add water pressure...
  9. When you unscrew the gas cap, is there a pressure...

    When you unscrew the gas cap, is there a pressure build up inside? (gas cap slightly blows off)

    Try the reeds swap please
  10. Thread: Thar She Blows

    by xlint89
    Replies
    75
    Views
    4,052

    Thanks for the closure SL. This set up always...

    Thanks for the closure SL.

    This set up always had me interested. I still have all the parts to make it work laying around the house.

    Glad to hear she's back up and running. There was another...
  11. Replies
    2
    Views
    57

    Welcome to the Hulk. You did a good job thus...

    Welcome to the Hulk.

    You did a good job thus far. The only thing I can tell you haven't addressed is a leak down test of the engine. You may have an air leak causing you to go lean.

    Please...
  12. Absolutely. Make sure to remove the driveshaft. ...

    Absolutely. Make sure to remove the driveshaft.

    You can then run the engine on the garden hose like this. The reason we suggest running the engine for short periods of time is because the...
  13. Unfortunately, you do NOT have a Pro 785. That...

    Unfortunately, you do NOT have a Pro 785. That engine is a 700cc twin domestic engine. It's not the Fuji 3 cylinder 785cc.

    Please post a picture of the ski.
  14. Sorry, I meant try removing the gas cap while...

    Sorry, I meant try removing the gas cap while running on the garden hose and see if the water separator fills up fully.

    You do not have reserve. You have a low fuel indicator and what we call...
  15. Replies
    4
    Views
    79

    That O ring should be making the seal. What...

    That O ring should be making the seal.

    What was the direct source of the leak?
  16. Replies
    9
    Views
    286

    FS - Parts Very nice. Thanks for the heads up.

    Very nice. Thanks for the heads up.
  17. Welcome to the Hulk. You've done some reading,...

    Welcome to the Hulk.

    You've done some reading, that's good.

    Yes, get rid of the clear fuel lines. It's too soft for use in front of the fuel pump. The pump creates vacuum and needs to pull the...
  18. Replies
    16
    Views
    1,082

    Almost looks perfectly machined. Weird....

    Almost looks perfectly machined. Weird....
  19. Replies
    2
    Views
    62

    Welcome to the Hulk. Check everything the gray...

    Welcome to the Hulk.

    Check everything the gray fuels lines are attached to. They seem to create a green "goo" that can cause fuel starvation issues.

    Meaning fuel pick up tube in the fuel tank,...
  20. Replies
    4
    Views
    79

    Welcome to the Hulk. Rainbow colors in water...

    Welcome to the Hulk.

    Rainbow colors in water is oil or gas. Most likely coming out of your exhaust. Meaning you're not burning it fully.

    When your ski is acting up, remove the seat and feel all...
  21. Now that is really cool. Never knew anything like...

    Now that is really cool. Never knew anything like that ever existed.

    Thanks for posting.
  22. Keith, that is really interesting. Thanks for the...

    Keith, that is really interesting. Thanks for the pics.

    One question though, what is holding that boat in the last pic upright?
  23. Replies
    38
    Views
    1,011

    If you attempt to reseal the exhaust manifold,...

    If you attempt to reseal the exhaust manifold, make sure you follow the proper bolt torquing sequence and in increments. Meaning follow the right order and 5 ft. lbs on all, then 10 ft. lbs. on all,...
  24. Replies
    3
    Views
    116

    Metric M8 x 1.25

    Metric M8 x 1.25
  25. So envious.... Glass flat water. Send some my...

    So envious....

    Glass flat water. Send some my way please. i got some testing to do.

    Enjoy it
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4