Search

Type: Posts; User: madtom

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    3,302

    Any recommendations for jet changes to make up...

    Any recommendations for jet changes to make up for the fact the factory is all about emissions and less about longevity. Info for the CDCVs is very limited and there is little in the way of DIY...
  2. Replies
    5
    Views
    162

    I just had to remove my pump from my 2003 12F stx...

    I just had to remove my pump from my 2003 12F stx for weeds.... was pain in the ass to get aligned but you will know when you do. Need to slide it off just enough to change orientation of impelled a...
  3. Replies
    1
    Views
    90

    It uses the CDCV keihin carbs. You can find...

    It uses the CDCV keihin carbs. You can find them on Ebay for decent prices. Here is a example
    ...
  4. Replies
    3
    Views
    178

    Oil tank uses a pump to go into engine and would...

    Oil tank uses a pump to go into engine and would not fill up completely as you have described... this was more of a super fogging oil type treatment to protect engine from corrosion.

    Sounds...
  5. Replies
    28
    Views
    1,904

    I have taken your advice and hooked up to the...

    I have taken your advice and hooked up to the pump. I know on the 900 since it only has a fitting coming from the pump it picks up any vegetation the pump eats. 12f seems to keep it out.
  6. Replies
    28
    Views
    1,904

    So I think the project phase is complete. I had...

    So I think the project phase is complete. I had to reconnect the cooling lines to the muffler as I had done the single waterbox mod and ditched the 2nd waterbox. The hull exit line was hooked up on...
  7. Replies
    28
    Views
    1,904

    Sean, Thanks I will let you know if it helps

    Sean,

    Thanks I will let you know if it helps
  8. Replies
    28
    Views
    1,904

    Was able to lift the engine this afternoon and...

    Was able to lift the engine this afternoon and pull the driveshaft/ bearing carrier. All back together now. it gets warm still while on hose but much cooler than yesterday. I must have been...
  9. Replies
    8
    Views
    1,022

    2003 12f. I pulled the engine and put a new...

    2003 12f. I pulled the engine and put a new thru hull bearing in. i apparently left it on the hose for too long. 45 minutes to cook the rest of the moisture out of the oil system. I had a...
  10. Replies
    28
    Views
    1,904

    while I am waiting for a dedicated time block to...

    while I am waiting for a dedicated time block to pull the engine... hopefully tomorrow.. I built some mounts for the sediment filters that are going onto the intake lines. I know that the factory...
  11. Replies
    69
    Views
    2,864

    Sean, Any difference in the maps between the...

    Sean,

    Any difference in the maps between the different year ECUs? I have a 03 http://greenhulk.net/forums/attachment.php?attachmentid=449970&stc=1

    It would be nice if there was just a way to...
  12. Replies
    8
    Views
    1,022

    were you able to determine why it was getting...

    were you able to determine why it was getting warm? I just replaced the fitting in my ski and same thing. thinking probably that i let the rtv setup for too long before dropping the engine in.... ...
  13. Replies
    28
    Views
    1,904

    I ran it on the trailer again today just checking...

    I ran it on the trailer again today just checking everything out. after 30 minutes or so i shut it off and was checking temperatures. Does the thru hull bearing and carrier get warm? it was...
  14. Replies
    28
    Views
    1,904

    So quick update on where I am at. IT IS ALIVE ;)...

    So quick update on where I am at. IT IS ALIVE ;)

    was busy with work and a wedding last couple of weeks so never got to put any time in on the ski. today was the first full day that was nice...
  15. Replies
    28
    Views
    1,904

    I did. It was an early model not affected by the...

    I did. It was an early model not affected by the recall. Part number on the tank was 51004-3739 and it came from an 04.
  16. Replies
    28
    Views
    1,904

    intake and exhaust manifold on

    So was able to get some work in today. lots of discovery learning](*,) as this is my first time putting everything into the ski.

    I mounted exhaust manifold, 4 into 1..... discovered that it is...
  17. Replies
    28
    Views
    1,904

    quick update, So this evening i was able to...

    quick update,

    So this evening i was able to finish torquing the engine to its mounts and start the on the cooling lines. I was able to run all cooling lines on the engine. I left a little...
  18. Replies
    28
    Views
    1,904

    any benefit of using anti-seize in the 4 into 1...

    any benefit of using anti-seize in the 4 into 1 connection to the manifold? i lost 3 bolts removing existing manifold and lost one with the ebay replacement. Just trying to reduce issues down the...
  19. if you need to upgrade the valvetrain use the...

    if you need to upgrade the valvetrain use the APE items....not overpriced and same quality

    http://aperaceparts.com/water/watervalvetrain.html
  20. Replies
    28
    Views
    1,904

    Update. So today the bearings came in.... but...

    Update. So today the bearings came in.... but while i was waiting i have repainted the intake with VHT anodized base and color engine paint. Painted the exhaust manifolds with VHT epoxy paint after...
  21. Replies
    15
    Views
    1,113

    I went thru the same thing with my 900 stx when...

    I went thru the same thing with my 900 stx when rebuilding it last winter.....
    So running the water line from manifold to pump bulkhead.....and what do I find. ....low and behold the water line...
  22. Replies
    28
    Views
    1,904

    Some progress this weekend. I was able to...

    Some progress this weekend.

    I was able to finish install of the larger 04 and later 16.5 gallon tank in place of the original 14.5 gallon

    larger tank installed...
  23. Replies
    2
    Views
    737

    FS wondering if you still have this timing plate?

    wondering if you still have this timing plate?
  24. Replies
    28
    Views
    1,904

    Today's update, Was able to finish the wiring...

    Today's update,

    Was able to finish the wiring harness tonight and start the fuel tank swap. Putting the 51004-3739 16+ gallon tank in place of the original 14.5 gallon from the 03. Still waiting...
  25. Replies
    10
    Views
    1,382

    Since the cams are different would it be useful...

    Since the cams are different would it be useful to swap the 15f cams into the 12f for performance upgrade if you modded the exhaust or upped the fuel pressure with a FPR by a few pounds? Trying to...
Results 1 to 25 of 35
Page 1 of 2 1 2