Search

Type: Posts; User: Myself

Page 1 of 8 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    1
    Views
    121

    You should NOT hear bubbling when blowing into...

    You should NOT hear bubbling when blowing into the return line. The return dumps out freely into the top of the baffle. The tank would have to be filled up to the neck to hear bubbling! Check the...
  2. Replies
    3
    Views
    120

    Threebond if the surfaces are scratched or pitted...

    Threebond if the surfaces are scratched or pitted up. Otherwise clean surfaces with new gaskets require nothing, just assemble dry. If you just want extra insurance the copper spray is great.
  3. Thread: 255 rebuild

    by Myself
    Replies
    4
    Views
    272

    Yep,.....the service manual. Everything is in it...

    Yep,.....the service manual. Everything is in it and pretty well written. Any hangups or things you don't understand can be asked on the forum and somebody will have an answer. All I can think of...
  4. Replies
    1
    Views
    86

    Ohm the primary side (where the connector hooks...

    Ohm the primary side (where the connector hooks up), should be low ohms, like around 1-1.5 ohms.
    Ohm the secondary (what touches the spark plug). One lead there and one to either side of the...
  5. Replies
    4
    Views
    236

    Sometimes an ECU goes bad. The last one I sent...

    Sometimes an ECU goes bad. The last one I sent for repair was keeping one injector open and flooding a cylinder. If it's actually doing this it will hydrolock. Black plugs are just very rich not...
  6. Replies
    16
    Views
    544

    Sorry, yes. Basically just step back and watch...

    Sorry, yes. Basically just step back and watch for pink instead of clear in the general area under the pump. A bit will spit out of the exhaust, a bit will spit out of the pissers, and of course from...
  7. Replies
    7
    Views
    323

    What?!! You must ride like a grandma lol!

    What?!! You must ride like a grandma lol!
  8. Replies
    16
    Views
    544

    I also use the flush ports. I have a garden hose...

    I also use the flush ports. I have a garden hose fitting clamped to a 2ft length of hose. Screws right into a 'Doo and Kawi, and into the adapter on a Yamaha. On the Yamaha I also use a pair of hose...
  9. LOL! I was going to say the exact same thing....

    LOL! I was going to say the exact same thing. 2009 or newer with a non supercharged 1.8L. I'd go for the Cruiser with the hip support seating but don't let it be a deal breaker cause you can always...
  10. Replies
    4
    Views
    236

    Most likely throttle cable mis-adjusted and TPS...

    Most likely throttle cable mis-adjusted and TPS giving the ECU signal to enrich the mixture. Check that there is slack in the cable and that all the hoses to the IAC motor are hooked up.
  11. Replies
    7
    Views
    323

    I mean......I know it's the time of year for...

    I mean......I know it's the time of year for everything pumpkin spice but COME ON!!!

    The electrode does not show much wear and I also don't see much (if any) carbon buildup. Guessing less than 15...
  12. Replies
    16
    Views
    544

    Here's how I do them. Have you seen pics of what...

    Here's how I do them.
    Have you seen pics of what moisture does to these Kawi pumps.....YIKES! Fill the tank with non ethanol.
    I use Lucas ethanol safegaurd to treat the fuel first.
    I use a 2psi...
  13. I'd run it. Bet it will do fine.

    I'd run it. Bet it will do fine.
  14. Replies
    4
    Views
    160

    Clean the PV passage and place a new valve down...

    Clean the PV passage and place a new valve down in it. Check to see that it's not protruding into the cylinder while in the closed position.
  15. Replies
    2
    Views
    135

    The easiest hull to mount it in will be...

    The easiest hull to mount it in will be Superjet.....any year.
  16. I have replaced several Kawi triple CDI's because...

    I have replaced several Kawi triple CDI's because of a no fire on one cylinder. I just tested out a 900STX this evening....no fire on front cylinder after only 2-3 minutes then misfiring badly on...
  17. Replies
    4
    Views
    160

    Normally, when I see that, the shoulder in the...

    Normally, when I see that, the shoulder in the cylinder is worn. It allows the valve to drop a bit lower than it should and kiss the piston. Of course.....it leads to a broken valve.
  18. Replies
    7
    Views
    337

    Spark plugs can fire just fine out laying next to...

    Spark plugs can fire just fine out laying next to a ground and still be bad. Ohm them from connecting tip to the hex, if they read any ohms they are bad and the spark shorts to ground when the plug...
  19. Replies
    1
    Views
    77

    Purple and red/purple are 12v+ and black is...

    Purple and red/purple are 12v+ and black is ground. The gauge should power up and display something on the lcd screen.

    If not, hit me up, I probably have a working one around I'd sell for $150.
  20. Worn bendix or case still won't cause an engine...

    Worn bendix or case still won't cause an engine to kickback or try and start backwards. Timing will though.
  21. Replies
    6
    Views
    115

    Place an ad on Facebook for a JS550 or Superjet....

    Place an ad on Facebook for a JS550 or Superjet. Then explain.....'Now that I have your attention, I need somebody in my area to epoxy this." Any serious stand up jet ski rider is also familiar with...
  22. I've seen this before and your original stator is...

    I've seen this before and your original stator is probably fine. The timing circuit in the cdi probably crapped and it's trying to light off at the wrong times. Take the plugs out. Bring front...
  23. Replies
    10
    Views
    276

    The used one will be just fine. If good used...

    The used one will be just fine. If good used parts are still in spec then it's a GO!!
  24. This was a common issue on stock 62T 701 powered...

    This was a common issue on stock 62T 701 powered Waveventures. It's a heavy underpowered machine. Now you've got even less power AND it's overpropped. I'm betting it's having a real tough time with...
  25. It would probably run just fine with 38psi popoff...

    It would probably run just fine with 38psi popoff but normally the 800 likes around 50psi +/-
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4