Search

Type: Posts; User: xlint89

Page 1 of 8 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    25
    Views
    567

    Not sure that's going to work? I don't think...

    Not sure that's going to work?

    I don't think you have enough height on the side rails. You will most likely hit on the "V" before the ski rests on the rails.

    Notice how I had to cut the 2X for...
  2. Good suggestions from those guys. ^^^^ Piston...

    Good suggestions from those guys. ^^^^

    Piston wash is the carbon residue on top of the piston domes. That is a great indicator of what is happening internally.

    Remove the spark plugs. Roll the...
  3. Replies
    6
    Views
    1,944

    Yes, use a good below the water line silicone...

    Yes, use a good below the water line silicone sealant on the screws and around the hole.
  4. Right ^^^^ What's it doing or not doing? As...

    Right ^^^^

    What's it doing or not doing?

    As many details as possible please.
  5. Replies
    9
    Views
    465

    Yes, I know. I have come to find the sequence...

    Yes, I know.

    I have come to find the sequence in which you torque the nuts has some input on final alignment.
  6. Replies
    47
    Views
    4,833

    I remember reading the additional clearance...

    I remember reading the additional clearance between the trailing edge of the impeller and the pump vanes was to possibly allow small rocks to get by reducing damage to the impeller and vanes....
  7. Replies
    5
    Views
    128

    If it slides right in and bottoms out like K447...

    If it slides right in and bottoms out like K447 says, you should be good.

    If it binds up prior to bottoming out, I would suggest adjusting the alignment.
  8. Replies
    9
    Views
    465

    If alignment is off, yes you loosen engine mount...

    If alignment is off, yes you loosen engine mount nuts and add or subtract shims from between the motor mount and the engine mounting plates. Then you retorque the nuts and check alignment again. It's...
  9. Replies
    47
    Views
    4,833

    The Hot Seat element was angled. The OEM was...

    The Hot Seat element was angled. The OEM was straight. There might be a chance the OEM could be modified to fit the Hot Seat?

    What Casey says about the impeller is true. I wrote the one in the pic...
  10. Replies
    47
    Views
    4,833

    That's really cool you were able to find an...

    That's really cool you were able to find an ignition.

    The element for the Hot Seat flame arrestor isn't actually a filter. Just a screen mesh for preventing fire. I'm sure you knew that though.
    ...
  11. Replies
    15
    Views
    9,025

    Welcome to the Hulk. I am not a fan of clear...

    Welcome to the Hulk.

    I am not a fan of clear fuel hose. If it's soft, it can collapse under vacuum. And it normally gets really brittle and hard with age. Reinforced rubber hose is recommended.
    ...
  12. Replies
    24
    Views
    886

    OK, that sounds promising. I hope it's good to...

    OK, that sounds promising. I hope it's good to go.

    Got to wait a while to know for sure.

    Thanks for the offer, but you did all the work. Have one for me.
  13. Welcome to the Hulk. If you look at the...

    Welcome to the Hulk.

    If you look at the fittings, they have abbreviated markings on the sender indicating what they are intended for.

    main = main supply

    RES = reserve fuel supply

    Vent = ...
  14. Replies
    24
    Views
    886

    I hope it works for you. Aftermarket stators...

    I hope it works for you.

    Aftermarket stators have been hit or miss.

    I thought you were on the hunt for a good used OEM?
  15. Replies
    25
    Views
    567

    +1 That is the type I have and never had an...

    +1

    That is the type I have and never had an issue using.
  16. Replies
    25
    Views
    567

    Not pictured there were the 2 Pro 785 at the...

    Not pictured there were the 2 Pro 785 at the house.


    Yes, I have issues....... Only being able to ride 1 at a time is also one of them.
  17. Replies
    25
    Views
    567

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=481752&stc=1

    Not the best pic, but you can see what I did
  18. Replies
    25
    Views
    567

    I don't know the make of the sling I have, other...

    I don't know the make of the sling I have, other than being for a 3 person ski. Never seemed to have an issue lifting/fitting the MSX 140.

    I've always made my own PWC carts from wood. First one...
  19. Replies
    24
    Views
    886

    New with a warranty???? What did you buy?

    New with a warranty????

    What did you buy?
  20. Replies
    10
    Views
    989

    Didn't feel like cutting out, just wouldn't rev...

    Didn't feel like cutting out, just wouldn't rev up as high as it should. (780 should turn 6500 RPM)

    My guess is the magneto was fine until higher RPM and heat built up, then caused the problem.
    ...
  21. Replies
    10
    Views
    989

    That's prob the best explanation you're going to...

    That's prob the best explanation you're going to get. ^^^^^

    No one dives into the why, they just disconnect or replace the MFD and move on.

    Have you ohm tested the magneto? I had a failing...
  22. Replies
    10
    Views
    989

    Welcome to the Hulk. K447 suggested everything...

    Welcome to the Hulk.

    K447 suggested everything I would have.

    The oil film inside the waterbox raises an eyebrow though.

    Sounds like over rich condition, or missing cylinder.

    How does the...
  23. Replies
    24
    Views
    886

    That sucks. Hopefully the seller is a stand up...

    That sucks. Hopefully the seller is a stand up guy.
  24. Replies
    24
    Views
    886

    So it is. Perfect. Hope the magneto works out...

    So it is. Perfect. Hope the magneto works out for you. Keep us posted please
  25. Replies
    47
    Views
    4,833

    I cannot find any info for you on the MSD, but...

    I cannot find any info for you on the MSD, but Hyoctane seems to have a working unit in his ski. Maybe he can chime in on this for you.

    1999 Pro 785 Superstock Build (greenhulk.net)
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4