Search

Search: Search took 1.00 seconds.

  1. Replies
    23
    Views
    1,841

    I was thinking of pulling the hose from the blow...

    I was thinking of pulling the hose from the blow off valve to spray in the fogging oil
  2. Replies
    23
    Views
    1,841

    MAP sensor hose.

    MAP sensor hose.
  3. Do not rule out the option of buying a used head,...

    Do not rule out the option of buying a used head, I bought one from a salvage yard that sells motorcycles and just happened to call just for shits and grins, long story short they had a gold mine in...
  4. http://www.greenhulk.net/forums/attachment.php?att...

    http://www.greenhulk.net/forums/attachment.php?attachmentid=434653&stc=1
  5. I knew someone would make a comment like this!...

    I knew someone would make a comment like this!
    This rig has been used on 15 to 20 skies over the last 20+ yrs and I only have it in the air without a cart under it while spraying, all the prep work...
  6. Replies
    2
    Views
    418

    Start engine (dry, no garden hose) and blip the...

    Start engine (dry, no garden hose) and blip the throttle firmly a few times. That should blow most of the excess water from the water box.

    I would drain the fuel take as much as possible. Gasoline...
  7. Replies
    584
    Views
    43,572

    View Post

    Yep no problem 86mph but donít think fx will go much more after 86mph, big ass whale lol
  8. Replies
    304
    Views
    37,583

    https://youtu.be/gg_dVgbp6UM Long overdue...

    https://youtu.be/gg_dVgbp6UM

    Long overdue video. Finally finished. This was a video of my unboxing pre Holidays!
  9. Replies
    584
    Views
    43,572

    428380 Block off plate is on stock fx ride...

    428380
    Block off plate is on stock fx ride plate.... my Jimís speed cut plate should be arriving soon, canít wait for speed plate to c gains
  10. Replies
    819
    Views
    114,512

    Why diss Mexico for any of this? In the 21st...

    Why diss Mexico for any of this? In the 21st century the country of origin rarely affects the quality of manufactured goods. Rather it is the parent company alone who is responsible for engineering,...
  11. Welcome to 9 years ago

    Welcome to 9 years ago
  12. Poor performance on '18 rxtx storage box lid

    Ok, So the storage box lid is adjustable. and any one that is slamming theres shut should not be. if you read my posts 9, and 10. you will see that i just was dealing with the issue. and learned a...
  13. Make sure you put anti-sieze on the drive shaft...

    Make sure you put anti-sieze on the drive shaft threads!
    Every time you remove an impeller, clean the threads with brake cleaner and recover the threads with anti-sieze....with the R&D washer kit...
  14. Replies
    8
    Views
    844

    It cut off one time shortly after I put it in the...

    It cut off one time shortly after I put it in the water, idling around, and the battery was weak, almost didn't get it restarted. Finally did, ran great after that....ran 70 on the gps. Can the...
  15. No when putting a pump seal kit you have to cut...

    No when putting a pump seal kit you have to cut the flat part out of the stock one a use that.
    When leaving that out water rushes up between there and causes drag.
  16. http://partsfinder.onlinemicrofiche.com/4tec/showm...

    http://partsfinder.onlinemicrofiche.com/4tec/showmodel.asp?Type=13&make=yamahapwc&a=239&b=19&c=0&d=2015%20FX%20SVHO%20[FC1800P]%20INTAKE%20AND%20RIDE%20PLATE%20ASSY
    Should not on a fx should have ...
  17. Many times the leaks into the hull is caused by a...

    Many times the leaks into the hull is caused by a leaky transom. It's a pretty easy job to rip it off, clean, align, seal and bolt back on.
  18. That's normal. Water from the exhaust landing on...

    That's normal. Water from the exhaust landing on the ride plate. The ride plate is not sealed between the intake grate.
  19. Replies
    13
    Views
    1,825

    As the engine consumes fuel from the tank, air...

    As the engine consumes fuel from the tank, air must be allowed to enter the fuel tank to avoid creating a vacuum in the fuel tank. The tank is vented to the outside of the hull (when the vent tube is...
  20. Confirmed 2 mph gain with jim's modded plate. Big apology to jim's performance

    So I know this isn't news to anyone already running a plate modded by Jim, thats not the reason for the thread. The point of this is simply to try to right my wrong. I jumped the gun and posted a few...
  21. Replies
    22
    Views
    2,854

    Fx svho prop pitch help

    2016 FX SVHO

    MOD LIST:
    - BOV
    - Intake Grate (Riva)
    - Stock Modded RidePlate
    - Free Flow Exh. (After Market)
    - Ribbon Delete
    - Engine Cooling Kit
    - Ecu Flash 8650rpm --In Salt 8410rpm...
  22. Replies
    10
    Views
    4,828

    I finally have the 2015/2016 scanned. Is it ok to...

    I finally have the 2015/2016 scanned. Is it ok to post it here?
    I do not want to get in trouble.
    If not allowed i will remove.

    - SORRY
    Removed, after some very valid points from other members.
  23. Replies
    13
    Views
    2,705

    You just answered your own question with your...

    You just answered your own question with your question.....And if the ICer was leaking it would enter through the intake manifold....
  24. Replies
    14
    Views
    1,344

    Pretty sure you will need bigger injectors as...

    Pretty sure you will need bigger injectors as well.
  25. Replies
    15
    Views
    1,769

    I put er in the water today. My arms are killing...

    I put er in the water today. My arms are killing me. Thought the beast was going to pull them out of the socket. Gauge was reading just under 70mph. I never expected for it to pull that hard. Thank...
Results 1 to 25 of 25