Search

Type: Posts; User: mpirpre

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    210

    Sounds good! Thanks nmpeter!

    Sounds good! Thanks nmpeter!
  2. Replies
    4
    Views
    210

    Thanks! So if i put the driveshaft and pump in...

    Thanks!

    So if i put the driveshaft and pump in temporarily to spin test the motor and then the shop removes the driveshaft for the alignment will there be oil coming out of PTO? I hope they don't...
  3. Replies
    4
    Views
    210

    Starting 2002 GTX 4tec

    Good afternoon, over winter I removed the engine in my 2002 GTX 4tec for some repairs and now engine is back in, all wiring connected, all coolant hoses connected. I left the jet pump and driveshaft...
  4. Replies
    11
    Views
    337

    yes I am checking the clearances with the old...

    yes I am checking the clearances with the old bolts. I got a new set of OEM bolts that will go in on final assembly

    i wish I would have know that about the WSM bearings cause I bought a whole set...
  5. Replies
    11
    Views
    337

    Ok. Perfect! Thanks for all your help!

    Ok. Perfect! Thanks for all your help!
  6. Replies
    11
    Views
    337

    Ok. Thanks! When you check the clearance with...

    Ok. Thanks! When you check the clearance with plastigauge do you torque to 33ft lb + 90 degrees or is torquing to 33 enough just for checking the clearance?
  7. Replies
    11
    Views
    337

    Ok. Thanks. So there’s nothing written in the...

    Ok. Thanks. So there’s nothing written in the manual for minimums?
  8. Replies
    11
    Views
    337

    I saw those specs. How would you figure out the...

    I saw those specs. How would you figure out the min and max clearances for the connecting rod bearings using those specs?
  9. Replies
    11
    Views
    337

    Gtx 4tec connecting rod big end clearances

    Good day everyone. Just curious if anyone had specs for connecting rod big end clearance on these 4tec motors. I have a manual and all they list is the service limit. Is there a min and max spec?
  10. Replies
    23
    Views
    791

    Anyone have any suggestions?

    Anyone have any suggestions?
  11. Replies
    23
    Views
    791

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=456979&stc=1

    http://greenhulk.net/forums/attachment.php?attachmentid=456979&stc=1hereis what it looks like
  12. Replies
    23
    Views
    791

    I will post a pic when I get back home later

    I will post a pic when I get back home later
  13. Replies
    23
    Views
    791

    You are right. Just checked it out and there is a...

    You are right. Just checked it out and there is a noticeable lip where the thrust bearing rides on the block. Could I just take some sand paper and make it flat again to gain the needed clearance?
    ...
  14. Replies
    23
    Views
    791

    Alright so I just measured it and I’m getting...

    Alright so I just measured it and I’m getting .002”. What could I do to get a bit more axial play? Could I sand down the backside of the thrust washer a bit with some 400 or 600 grit sandpaper?
  15. Replies
    23
    Views
    791

    Yes, i am aware of that. I will check it with a...

    Yes, i am aware of that. I will check it with a dial indicator for sure!
  16. Replies
    23
    Views
    791

    ok, that's what i thought. Thanks for your help!

    ok, that's what i thought. Thanks for your help!
  17. Replies
    23
    Views
    791

    ok thanks, should you be able to feel .003" of...

    ok thanks, should you be able to feel .003" of movement? I will check it but just wondering if you should be able to feel it?
  18. Replies
    23
    Views
    791

    I tried sliding them in once the crank was in...

    I tried sliding them in once the crank was in place and it was too tight. the only way i could get them on was to put them on the block first and then slide the crank into place. That's why i think...
  19. Replies
    23
    Views
    791

    yes, half rings (thrust washers)

    yes, half rings (thrust washers)
  20. Replies
    23
    Views
    791

    I haven't checked it with a dial indicator yet...

    I haven't checked it with a dial indicator yet but when i put the thrust washers on the block and slide the crank in place, it is very tight and i have to wiggle the crank a bit to get it into...
  21. Replies
    23
    Views
    791

    crankshaft thrust washer question

    Hi everyone, i have a 02 GTX 155 that I am rebuilding the bottom end of the motor due to thrust washers getting chewed up due to improper alignment. The thrust washer did not spin but it did have...
  22. Replies
    0
    Views
    114

    2002 seadoo gtx driveshaft conversion

    Hi Everyone, Just about finished replacing crankshaft & thrust washers in my ski. After doing a bit of reading on here, it seems like 2004 + up driveshafts were a little bit shorter than the 02's to...
  23. Replies
    0
    Views
    142

    2002 seadoo GTX 4tec driveshaft

    Hi Everyone, Just about finished replacing crankshaft & thrust washers in my ski. After doing a bit of reading on here, it seems like 2004 + up driveshafts were a little bit shorter than the 02's to...
  24. Replies
    15
    Views
    911

    Anyone?

    Anyone?
  25. Replies
    15
    Views
    911

    Ok. Thanks for all the replies! My next...

    Ok. Thanks for all the replies!

    My next question does the head need to come off to replace the crankshaft? The manual says it does but is there another way to do it?

    also I have been doing some...
Results 1 to 25 of 43
Page 1 of 2 1 2