Search

Type: Posts; User: TJS0712F

Search: Search took 0.01 seconds.

  1. Sticky: Mowhawk. I have commented on those vids. Cool...

    Mowhawk. I have commented on those vids. Cool idea. Do you have any vids of you fabricating the stainless wear ring. The Kawi wear rings are very thin. So locating a piece of UHMW(whatever it is...
  2. Sticky: Ok had it out all weekend on the sound. Got 52MPH...

    Ok had it out all weekend on the sound. Got 52MPH on the dash (no GPS), full tank and 220lbs of me. I think this is about right.
    T.J.
  3. Sticky: Done. I must say new factory shafts have some...

    Done. I must say new factory shafts have some serious runout. Not like the real jet boat Berkeley shafts I am used to. I do not have a 4 jaw so getting this run out to a minimum was challenging when...
  4. Sticky: The ways were fully cleaned after this. I do have...

    The ways were fully cleaned after this. I do have a cutting board plastic but it woul not fit for what I was doing. I had a towel there but got blown away for the pic.
  5. Sticky: Short vid....

    Short vid.
    https://www.youtube.com/watch?v=NA0CoY23Z9A
  6. Sticky: I finally got around to machining /grinding down...

    I finally got around to machining /grinding down my impeller after I TIG welded it up using 312 filler rod. I cobled up a home made tool post grinder that I used a foredom shaft driven grinder. I...
  7. Sticky: [QUOTE=steve45;2717794]Cool! I didn't know you...

    [QUOTE=steve45;2717794]Cool! I didn't know you could buy replacement wear rings for Kawasakis. Did you get it from 'that place' in Florida?

    I had to replace the pump housing on my Ultra 150 over...
  8. Sticky: http://www.greenhulk.net/forums/attachment.php?att...

    http://www.greenhulk.net/forums/attachment.php?attachmentid=387586&stc=1
    Here is the impeller welded up. Next up OD grinding the impeller on the lathe and setting the clearance I am looking for.
    ...
  9. Sticky: http://www.greenhulk.net/forums/attachment.php?att...

    http://www.greenhulk.net/forums/attachment.php?attachmentid=387583&stc=1
    Once again on the Bridgeport drilling the hole for the factory set screw. This was fun....

    ...
  10. Sticky: http://www.greenhulk.net/forums/attachment.php?att...

    http://www.greenhulk.net/forums/attachment.php?attachmentid=387579&stc=1
    Cut out the wear ring with the dremmel tool. Being very very careful.
    ...
  11. Sticky: http://www.greenhulk.net/forums/attachment.php?att...

    http://www.greenhulk.net/forums/attachment.php?attachmentid=387577&stc=1
    Locking in the DRO


    http://www.greenhulk.net/forums/attachment.php?attachmentid=387578&stc=1
    Just kissed it with the...
  12. Sticky: http://www.greenhulk.net/forums/attachment.php?att...

    http://www.greenhulk.net/forums/attachment.php?attachmentid=387573&stc=1
    Puked pump. Nice.

    http://www.greenhulk.net/forums/attachment.php?attachmentid=387574&stc=1
    Bugger housing.
    ...
  13. Sticky: Replacing wear ring and repairing impeller 07-12F

    Sorry Long post.
    Ok Greenhulkers. This post is information only. I am not selling or pushing anything/anyone in this post, so please don’t ask. It is just basically how I did it for your viewing...
Results 1 to 13 of 13