Search

Type: Posts; User: mittens

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    154

    Roger that! just don't dip it in salt.

    Roger that! just don't dip it in salt.
  2. Replies
    3
    Views
    154

    Works but going to get the bike very wet...

    Works but going to get the bike very wet launching ha
  3. Replies
    6
    Views
    484

    If your on the limiter, pitch it up to drop rpms...

    If your on the limiter, pitch it up to drop rpms a little
  4. Replies
    9
    Views
    520

    So the though it the stage2/3 mods are causing...

    So the though it the stage2/3 mods are causing cavitation and then burning the stator vanes?
  5. Replies
    4
    Views
    322

    On the car your not changing the wheel, your...

    On the car your not changing the wheel, your changing the pulley, to spin it faster.

    Which is how raising the RPMS work. Putting in a new wheel, its more similar to swapping from P1 to a D1...
  6. Replies
    2
    Views
    178

    From what I remember most where not crazy fans of...

    From what I remember most where not crazy fans of he footwell drains other then storage.
  7. Replies
    309
    Views
    50,508

    The 98 mph was the one with the EFR 7163... flip...

    The 98 mph was the one with the EFR 7163... flip one page back and see him post that.

    I think 95 was the fastest he got it with a 6758, he also said the 6758 maxed out at 27Lbs on these motors.
  8. Replies
    23
    Views
    842

    Awesome info, thanks

    Awesome info, thanks
  9. Replies
    4
    Views
    411

    I know Julio / abracadabra, got his 98.1mph, 9500...

    I know Julio / abracadabra, got his 98.1mph, 9500 rpms/
    http://greenhulk.net/forums/showthread.php?t=236171&page=30&highlight=6758
  10. FS - Parts Sold. Can lock thread.

    Sold. Can lock thread.
  11. Replies
    4
    Views
    305

    I did a RRFR so I can adjust my AFRs for weather...

    I did a RRFR so I can adjust my AFRs for weather changes. Stock fuel pump. But ski had 19 hours on it when I started last season. some run tunes an trust its all correct. others use wide band and...
  12. Replies
    4
    Views
    305

    Last yea my set Up is my sig. i have a Riva...

    Last yea my set Up is my sig. i have a Riva cooling anoode fed off the factory intercooler. & a new separate feed for intercooler. So Basicly just like the worx kit.

    9300 rpm limiter in Alabama...
  13. I am sure Jerry will work with you. But...

    I am sure Jerry will work with you.

    But tapping manifold is not hard. Also I swear I have seen a Throttle body adapter that has a Nipple on it. so NOthing would be changed and not mess with ay...
  14. My old SHO was a 8850 limiter, but only pulled...

    My old SHO was a 8850 limiter, but only pulled 8500 ish WOT. no retainers. sold with 150 hours on it.

    Not saying it was smart but was fine ha.
  15. Replies
    29
    Views
    1,783

    I have no experience with one that the shaft...

    I have no experience with one that the shaft stays in the hull. All the ones I have dealt with Shaft and prop come out with pump. sorry no help
  16. Replies
    3
    Views
    213

    Search function will show ALOT of people saying...

    Search function will show ALOT of people saying the same asi 2 above and my self.

    Tap manifold. do not mess with MAP.
  17. Replies
    32
    Views
    1,638

    Yes should for sure, supercharger is RPM...

    Yes should for sure, supercharger is RPM dependent. where as the turbo should be fully spooled be 3500-4k. which is barley on plane.
  18. Replies
    24
    Views
    1,233

    Loosen mid shafe bolts, see if pump slide in. if...

    Loosen mid shafe bolts, see if pump slide in. if so, then tighten bolts and then adjust motor shims so all in line? that's how I would think. the mid shaft has the least amount of play to adjust.
  19. My SHO clutch lasted 122 hours, Replaced with...

    My SHO clutch lasted 122 hours, Replaced with SVHO 2014-2018 version and idler less then 30 hours it was done.

    all using Yamaha Lube with same C1 wheel not a big one.
  20. He is tracking correctly. Replace one at a time...

    He is tracking correctly. Replace one at a time with torque specs and should not touch chain.
  21. Translated: Seriously? And what is the...

    Translated:


    Seriously?
    And what is the reason why the new FX is slower?
    When I tested the new FX SVHO it seemed lighter, shouldn't it be better for more top speed?
  22. Replies
    16
    Views
    725

    Yes I am sorry GTX300 Limited

    Yes I am sorry GTX300 Limited
  23. Replies
    32
    Views
    1,638

    I am also weighing all parts that are coming off...

    I am also weighing all parts that are coming off ski, and weighing all parts going back on Not that it matters

    But just curious, the weight difference with a turbo, and all the hot pipes, vs...
  24. Replies
    16
    Views
    725

    Not that this is always the case, but I have a 2...

    Not that this is always the case, but I have a 2 seadoo budys

    one is a RXP-X 300
    one is a GTX 300 Limited

    The rxp-x did prop and Maptuner X tune
    The GTX did a speed limiter delete.

    The GTX...
  25. Starting them for 10-30 seconds is not a issue...

    Starting them for 10-30 seconds is not a issue with out water. they will heat up but not to anything significant that fast. can feal the exhaust manifold get warm after 30 seconds but that's about...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4