Search

Type: Posts; User: Pilotoat

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    3,794

    Hi DrewNJ, I just rebuilt the carbs and replaced...

    Hi DrewNJ, I just rebuilt the carbs and replaced the oil / fuel lines after a blown first piston. I also replaced the cylinder jug and new piston. My compression for the first new cylinder is 100,...
  2. Replies
    24
    Views
    2,932

    Yea horrible ����♂️ any thoughts on the...

    Yea horrible ����♂️

    any thoughts on the Compression? 100/120/120
  3. Replies
    16
    Views
    14,865

    I just rebuilt my MAG (Front Cylinder) New Jug...

    I just rebuilt my MAG (Front Cylinder) New Jug and Piston. I also cleaned all carbs out. I just did a compression test and the first cylinder is around 100 PSI while the other 2 are 120 PSI. This...
  4. Replies
    24
    Views
    2,932

    Turns out the temp sensor was not fully clipped...

    Turns out the temp sensor was not fully clipped in not allowing for spark. Fired right up and stayed running. Thank you all!!!

    now need to water test it and hope itís fixed and ready to go.
    ...
  5. Replies
    24
    Views
    2,932

    I did it was around 50. I’ll take a look to see...

    I did it was around 50. I’ll take a look to see if any air leak or issues.

    i used clear oil lines but wasn’t sure if fuel.net was strong enough for gas, so used marine black fuel lines. I may...
  6. Replies
    24
    Views
    2,932

    Yes everything was working properly. Long story...

    Yes everything was working properly. Long story short bought it used with blown piston in first cylinder. Replaced it and thought I was good to go only to find out I blew another one. I rebuilt...
  7. Replies
    24
    Views
    2,932

    Yep everything is hooked up. I primed the oil...

    Yep everything is hooked up. I primed the oil lines with a drill so oil is at each carb, just didn’t do anything for fuel.
  8. Replies
    24
    Views
    2,932

    Finally put back together. Started it without...

    Finally put back together. Started it without spark plugs hoping this would get fuel to the carbs since the lines are dry. This didn’t work and won’t start. I must be missing something.

    any...
  9. Replies
    24
    Views
    2,932

    Damm thanks! I’ll start taking the exhaust pipe...

    Damm thanks! I’ll start taking the exhaust pipe off cause I can’t get to the hoses.

    thanks again for the quick response.
  10. Replies
    24
    Views
    2,932

    Are we saying the diagram from partzilla is...

    Are we saying the diagram from partzilla is wrong? I have the fuel filter running to the front and the rear carb going to the tank.

    if this is backwards I guess I gotta take it apart and swap. ...
  11. Replies
    4
    Views
    177

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=472725&stc=1 http://greenhulk.net/forums/attachment.php?attachmentid=472726&stc=1
  12. Replies
    4
    Views
    177

    GP1200R Oil Pump

    Hi all,

    I redid the oil lines and was about to put the oil pump back on and the bracket snapped in half. I superglued it for now, but think I will try and soder it.

    should I just buy a new...
  13. Replies
    17
    Views
    1,809

    View Post

    What bit did you use to fit the oil pump? I canít seem to find one that fits the end that needs to spin.

    thanks!
  14. Replies
    214
    Views
    148,846

    Sticky: Thanks all! This group is great! I ended up...

    Thanks all! This group is great! I ended up getting a pneumatic staple gun and some marine fabric. I do wish I got thicker fabric, but wanted to give it a shot. Need to clean up some corners, and...
  15. Replies
    214
    Views
    148,846

    Sticky: Hi All, I am in the process of recovering my...

    Hi All,

    I am in the process of recovering my seat. I went and got some marine vinyl and going to try that route, but wanted to get everyone's thoughts. Should I leave the current OEM seat cover...
  16. Replies
    102
    Views
    7,115

    Did you also do the return line / drilling the...

    Did you also do the return line / drilling the carbs mod proposed by OSIDE? Trying to see if I use stock jetting or the recipe but keep accelerator pump intact and drill the air box.

    thanks!
  17. Replies
    31
    Views
    6,718

    This looks great! I am in the process of pulling...

    This looks great! I am in the process of pulling off my decals and noticed there is an added layer. Does anyone know if this is clear coat or what? Trying to see if I need to sand down the full...
  18. Replies
    214
    Views
    148,846

    Sticky: I love this color combination. Is the White lid...

    I love this color combination. Is the White lid and fenders just the standard Pure White from Color rite or did you repaint the hull?
  19. Replies
    76
    Views
    50,346

    Sticky: Sorry last dumb question, how to I access the...

    Sorry last dumb question, how to I access the Sticky or see what is on it?

    Thanks again!
  20. Replies
    76
    Views
    50,346

    Sticky: do you have recommended high and low screw turns...

    do you have recommended high and low screw turns with this combo for Stock GP1200R?

    I saw:

    110 Pilot
    120 Mains
    1.5 N/S
    95 Gram Spring

    High - 1.5 turns out
  21. Replies
    312
    Views
    206,165

    Sticky: Thank you will take a look. The issue is I keep...

    Thank you will take a look. The issue is I keep finding the recipe for a combination with aftermarket Flame Arrestor, and I have the standard airbox.

    Will keep looking.
  22. Replies
    76
    Views
    50,346

    Sticky: Thank you, but these refer to Aftermarket F/A's...

    Thank you, but these refer to Aftermarket F/A's (Flame Arrestors) chokes intact. I am assuming this is an aftermarket F/A which I do not have. Is there settings without the FA or does this change...
  23. Replies
    312
    Views
    206,165

    Sticky: Hi All, first post after reading countlessly over...

    Hi All, first post after reading countlessly over the year.

    I recently purchased a 2000 GP1200R FULLY STOCK with Cylinder 1 piston seized. I thought this was due to the oil line detached, so put...
  24. Replies
    76
    Views
    50,346

    Sticky: Hi All, first post after reading countlessly over...

    Hi All, first post after reading countlessly over the year.

    I recently purchased a 2000 GP1200R FULLY STOCK with Cylinder 1 piston seized. I thought this was due to the oil line detached, so put...
Results 1 to 24 of 25