Search

Type: Posts; User: Sage18

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds; generated 22 minute(s) ago.

  1. Replies
    18
    Views
    1,134

    View Post

    Yes sheís all torn apart. Pump and impeller are toast. The impeller was not even connected to the stub shaft. This is how it was when I took the cone off.
    471726
    471727


    I was concerned...
  2. Replies
    18
    Views
    1,134

    Yeah I told them it was a single one piece head....

    Yeah I told them it was a single one piece head. Here is the email I received.
    470448

    Looks like Jay from Sharps, near me, might have some options for me. He even has a one piece head with...
  3. Replies
    18
    Views
    1,134

    View Post

    Couldnít say no to this one 5 miles down the road.
  4. Replies
    18
    Views
    1,134

    View Post

    Thatís interesting, any way you could send it to me?
  5. Replies
    18
    Views
    1,134

    PLE25288A303. Written wrong on my...

    PLE25288A303. Written wrong on my registration......grrrr
  6. Replies
    18
    Views
    1,134

    View Post

    No itís a one piece head. The domes are not removable.
  7. Replies
    18
    Views
    1,134

    Recently acquired Matrix

    I recently acquired a 2003 Polaris Matrix. Hull ID PLE25288A303. It has UMI steering, and BP Sponsons Itís a little beat up but not terrible.

    470409

    Guy told me a cylinder was down so I...
  8. Replies
    15
    Views
    645

    1999 Polaris SLX Ebox locations

    When did the plastic box start? 97? 98? I always forget too
  9. Replies
    15
    Views
    645

    There is an space on the bottom side of your...

    There is an space on the bottom side of your ebox, that fits the same dimension of the top to your battery. Make sure you use the plastic insulating top to your battery so it does not make contact...
  10. Replies
    140
    Views
    27,597

    2001 Polaris Pro 1200 - Triple Pipe Project

    Howíd the 1200 ride? Compared to the 785?

    Sorry to hear you sold you skis, Hope everything works out for you, I really enjoyed all your input on here.

    Sage
  11. Replies
    6
    Views
    320

    WTB View Post

    Your picture didnít show up for me, is it the right side ď1Ē that you need? Iím going to mail them to PWC graphics this week. They are all the 2000 pro 1200 decals
  12. Replies
    12
    Views
    3,346

    Yeah tell us more please!

    Yeah tell us more please!
  13. Replies
    6
    Views
    320

    WTB View Post

    Iím sending in some tracings to PWC graphics for a 2000 Pro 1200 so they should have the artwork shortly.
  14. Replies
    28
    Views
    3,486

    View Post

    Fastest of the 90ís that you can pick up for 1000 bucks? You can probably find a beat up 1996 seadoo XP 787 motor that might run but needs a piston, or carbs rebuilt, they do around 52-54 if...
  15. Stainless Steel replacement Screws for Mikuni Super BN38/40i/44/46 Carburetors

    Hey everyone K447 thought I should post this on here. This might help a bunch of you when you rebuild your carbs.

    I have rebuilt many jet ski carburetors over the years and always wondered why...
  16. View Post

    I donít think I have but I can put a thread up tonight. It has all the internal screws for quite a few of the mikuni carbs on skis and in stainless steel Philips drive too.
  17. Where to install jetworks valve on 2000 SLX

    Just found them. This is what I have left.

    466531
    No biggie.
    PM me your address, Iíll send them out in the morning. How many do you need? Iím at the post office all the time I sell...
  18. Hey, sorry for the delay, been out enjoying the...

    Hey, sorry for the delay, been out enjoying the water!

    Mine is installed on the mag side of the exhaust water outlet. The flow arrow is facing down. The delrin ball size I ordered was 10mm....
  19. Replies
    3
    Views
    278

    View Post

    Thanks Iíll check it out tonight. Can I find the exact size anywhere or just go off my measurements with a caliper?
  20. Replies
    3
    Views
    278

    Polaris gas cap O-ring size

    Specifically looking for the size of the O-ring seal on the gas cap for a 2000 Polaris Pro785. Polaris part number is 5411305. Iím going to measure it tonight but was wondering if anyone had a...
  21. Replies
    6
    Views
    491

    I seem to remember a truck engine oil thickening...

    I seem to remember a truck engine oil thickening up when using two different types of oil but not sure what it was.

    Iíve never used the Klotz - benol, I assume itís a decent oil? Either way I...
  22. Replies
    6
    Views
    491

    Thanks for your input. My thought was to just...

    Thanks for your input. My thought was to just keep running the same oil he had in it. I emptied the tank anyways and cleaned it out. Along with new fuel lines and filter so itís ready for a fresh...
  23. Replies
    6
    Views
    491

    View Post

    Thanks. Yeah Iíve always wanted one and when I saw it I took a 800 mile drive. Ha ha and yeah my wife thinks Iím crazy. I assume that you did your research on that oil. Iíve heard a few good...
  24. Replies
    6
    Views
    491

    Polaris Octane oil

    I just picked up a nice 2002 Octane. Carbs were rebuilt but I need to do the fuel lines today. I was going to run it this weekend but I donít have the oil the previous owner was using in it. ...
  25. Replies
    0
    Views
    254

    1996 seadoo XP fuel question

    I rebuilt the carbs with mikuni kits and replaced all the fuel lines last year on a ski that has been sitting for 14 years. The fuel system is all new. Ran great last year but before I put it on...
Results 1 to 25 of 116
Page 1 of 5 1 2 3 4