Search

Page 1 of 2 1 2

Search: Search took 1.00 seconds.

  1. Replies
    51
    Views
    12,315

    My original clutch went at 90 hours, literally...

    My original clutch went at 90 hours, literally the first ride after I switched from Yamalube to Rotella 5w40. I do a lot of bay riding where it is choppy. It could be coincidence but I switched back...
  2. Thread: Rideplate

    by silver93t
    Replies
    9
    Views
    2,251

    My stock plate bounced so I went to R&D. I was...

    My stock plate bounced so I went to R&D. I was happy with it until I increased the boost, then it started bouncing. Remember that as speed goes up and riding conditions change, your plate/shim setup...
  3. Replies
    9
    Views
    1,145

    Sounds like its time to find a better dealer with...

    Sounds like its time to find a better dealer with a knowledgeable service department.
  4. Replies
    18
    Views
    2,587

    No issues holding water with the Riva.

    No issues holding water with the Riva.
  5. I pack them as much as I can just like wheel...

    I pack them as much as I can just like wheel bearings. You want a grease that will stick and not fling off.
  6. I'm super happy with mine. Made a huge...

    I'm super happy with mine. Made a huge difference. I tried other aftermarket plates in the past and I just wasn't happy with them in the rough water I ride in.
  7. Replies
    138
    Views
    11,824

    I'm gonna laugh when you blow up.

    I'm gonna laugh when you blow up.
  8. Replies
    138
    Views
    11,824

    A richer a/f results in cooler cylinder temps and...

    A richer a/f results in cooler cylinder temps and exhaust gas temperatures as well as lowering the detonation threshold. If you are in the 12's under boost then you can easily by in the 16s under...
  9. Replies
    138
    Views
    11,824

    I highly doubt that. I've know him for years and...

    I highly doubt that. I've know him for years and he has always come through when I needed a part or tech support. Besides, you say your are the fastest so what are you worried about?
  10. Replies
    138
    Views
    11,824

    Too funny. I'll bring the beers and popcorn.

    Too funny. I'll bring the beers and popcorn.
  11. Replies
    16
    Views
    2,817

    My skis sit outside covered on the trailer all...

    My skis sit outside covered on the trailer all winter. I do the following:

    Wash and wax the skis.

    Fill the gas tanks and add fuel stabilizer.

    Run the skis without the hose for about a minute...
  12. Replies
    27
    Views
    2,612

    SOLD R Rated Freeflow for SHO skis

    I have a good condition R Rated freeflow exhaust. Should fit all SHO skis (FZR/FZS/FX). Includes all couplers and clamps. DOES NOT require cutting or modifying your stock exhaust so you can always...
  13. Replies
    287
    Views
    19,423

    Agreed the FX hull is better in the chop.

    Agreed the FX hull is better in the chop.
  14. Replies
    8
    Views
    703

    The only benefit I see is less heat soak over...

    The only benefit I see is less heat soak over multiple back to back runs.
  15. Replies
    24
    Views
    3,383

    Jim's SVHO plate is awesome

    Just wanted to thank Jim for the excellent work he did on the SVHO ride plate. I've ran stock, Riva, and R&D plates are was never happy with them. I tried all different shim combinations and either...
  16. I take the flush hose and put it against the...

    I take the flush hose and put it against the starboard pisser to backflush the intercooler.
  17. Replies
    423
    Views
    19,366

    Listen, its the little wheel that could. I build...

    Listen, its the little wheel that could. I build race cars for a living. I'm sick of fixing sh$t so I stay pretty conservative with the skis. I'll be happy with 80mph.
  18. Replies
    423
    Views
    19,366

    F@&CK that ski. Picked up a R&D regulator...

    F@&CK that ski. Picked up a R&D regulator tonight. Overnighted a wideband adapter and a few other goodies. ET LB going in. Anthony I'm coming for you.
  19. Replies
    12
    Views
    1,546

    I had both motors rebuilt. Needs the carbs...

    I had both motors rebuilt. Needs the carbs rebuilt and motors installed. I have all the pars I believe. Then get fired up and see what else it needs. I believe the trim cables are stuck and don't...
  20. Replies
    109
    Views
    12,956

    Every single powdercoated plate I've bought has...

    Every single powdercoated plate I've bought has chipped within 1 season. There's a reason why factory plates aren't coated.
  21. Replies
    5
    Views
    1,199

    3M 5200 for the transom. You don't want it to...

    3M 5200 for the transom. You don't want it to leak. Clean all the old sealant off the mating surfaces and wipe them down with acetone or brake cleaner before applying the sealant. I use permatex "the...
  22. Replies
    13
    Views
    3,164

    Found the issue. I guess the wire got frayed on...

    Found the issue. I guess the wire got frayed on something when I was working on the ski. Fixed now. 362683
  23. Replies
    9
    Views
    854

    A small amount of oil is normal. All forced...

    A small amount of oil is normal. All forced induction motors tend to have more blowby than a naturally aspirated motor. A breather with a catch can inline helps.
  24. Replies
    11
    Views
    1,572

    I wouldn't recommend running with it open. Block...

    I wouldn't recommend running with it open. Block it off by welding, jb weld, or a cap. OR you can use it as another water line for cooling the intercooler, oil cooler, or motor. I have 3 dedicated...
  25. Add some shims to the back bolts of the plate. I...

    Add some shims to the back bolts of the plate. I like to use stainless steel fender washers as they have a larger surface area and help distribute the load. Currently I have the R&D plate with the...
Results 1 to 25 of 44
Page 1 of 2 1 2