Search

Type: Posts; User: Gone_Ridin

Search: Search took 0.00 seconds.

  1. There are two ways to look at porting, increasing...

    There are two ways to look at porting, increasing volume or achieving efficiency. Without changing port timing or volume, efficiency can be gained by cleaning up and matching crankcase passages to...
  2. Replies
    6
    Views
    365

    The flaking nikisil has been mentioned often on...

    The flaking nikisil has been mentioned often on here and I think it was said there was a bad run of coatings. If so is there a specific s/n range to look out for or?...
  3. Replies
    9
    Views
    329

    a

    a
  4. Replies
    9
    Views
    329

    Because it overheats and there's no liquid in the...

    Because it overheats and there's no liquid in the manifold when I pull the plug once it's gotten hot. Yes I understand the flow and had put in a new thermostat
  5. Replies
    9
    Views
    329

    So, hooked up the diagnostic and looks like the...

    So, hooked up the diagnostic and looks like the previous owner swapped out the EMM and did not reprogram the injectors. Additionally he installed the injectors but did not install the insulators...
  6. Replies
    9
    Views
    329

    MSX 140 Rev issues

    My MSX 140 will not get up past 6200 rpm. Actually struggles to get over 5400 until i get the pump to cavitate then it'll climb to 6100/6200. If i get air after getting to 6 then it hits the...
  7. Replies
    15
    Views
    1,151

    So ended up buying and rebuilding 2 140s last...

    So ended up buying and rebuilding 2 140s last year which left the 150 on the back burner. Finally got around to pulling the engine out of it, since the Chinese flu has me locked down at home....
  8. Just came across this and I'm sure it's already...

    Just came across this and I'm sure it's already gone but thought I would take a chance. Still have it?!?
  9. Replies
    4
    Views
    355

    I've got a CanDoo so can program the injectors...

    I've got a CanDoo so can program the injectors but thought the same; buy a used one and start over with troubles so will just send mine away. Have sent Lakeside an email.
  10. Replies
    15
    Views
    1,151

    Will check those sensors and the tank vent before...

    Will check those sensors and the tank vent before pulling the engine. Hope it's that simple but compression was definitely low because my comp gauge is accurate.
  11. Replies
    15
    Views
    1,151

    Gauge is a Blue Point/Snap On Battery is new and...

    Gauge is a Blue Point/Snap On
    Battery is new and was fully charged, to make sure it was spinning I pulled both plugs so it wouldn't be dragging.
    Seasons coming to an end here shortly so will finish...
  12. Replies
    15
    Views
    1,151

    A compression test is easy, may I ask why you are...

    A compression test is easy, may I ask why you are resisting doing one? http://www.greenhulk.net/forums/images/smilies/icon_smile.gif

    Ya, I was hoping it was something else.
    Comp test was below...
  13. Replies
    4
    Views
    355

    MSX 140 Spark/Timing Issues

    Bought a "Not Running" MSX 140, package deal with a running one and 2 place trailer. Rebuilt it , indexed the crank, replaced crank seals and a few other things. Tried firing it up and i'm getting...
  14. Replies
    15
    Views
    1,151

    I took a look inside the cylinders with my...

    I took a look inside the cylinders with my endoscope and other than scuffing from moisture ingestion they don't look bad, couldn't see any nicasil peeling. Pulled the hoses off of both sides of the...
  15. Replies
    15
    Views
    1,151

    Noobie with a MSX150

    Bought an MSX150, started great on the trailer, everything looked good.
    Got it home, put it in the lake and it wouldn't start. Seemed to flood.
    Pulled it out and started on the trailer again,...
Results 1 to 15 of 15