Search

Type: Posts; User: txgp1300r

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    182
    Views
    85,241

    Whats it worth if we Dont tell your Dad !!! LOL ...

    Whats it worth if we Dont tell your Dad !!! LOL good job on attention to detail.
  2. You can always remove the wheel of the trailer on...

    You can always remove the wheel of the trailer on the side your going to be working. This allows lowering and tilting the ski for easier working. I also have a custom cart with big wheels I built for...
  3. Sticky: worked here ?

    worked here ?
  4. Replies
    16
    Views
    969

    I tapped it for a customer , I think he is using...

    I tapped it for a customer , I think he is using an AEM guage from Summit or something like that. it took longer to put the lathe in low tapping gear than the whole job took....very easy. the newer...
  5. Replies
    16
    Views
    969

    I did one of these yesterday....if you have the...

    I did one of these yesterday....if you have the aluminum pipe plug that unscrews from your manifold. I place the plug in a lathe and drill and tap for m18 x 1.5 thread...works very well.
  6. Replies
    13
    Views
    1,173

    the bump by your number #2 in pic is where you...

    the bump by your number #2 in pic is where you can drill a hole and install a 27mm long Time-sert 18mx1.5 for the sensor...I have done both...the older pipe plug manifolds are much easier.
  7. Replies
    7
    Views
    399

    your screwed if that is the pump area.....only...

    your screwed if that is the pump area.....only way I know to fix it is the remove the engine so that you can get at both sides with epoxy resin and glass.....bad spot for a crack. My uncles cracked...
  8. Replies
    7
    Views
    399

    look at the rubber hose that covers the drive...

    look at the rubber hose that covers the drive shaft in the bottom rear center of hull, transom plate, check for any damage to the ride plate mounting surface, and look for cracks around the prop area...
  9. Replies
    19
    Views
    1,396

    When it comes time to sell/ trade in your ski for...

    When it comes time to sell/ trade in your ski for a new model, you will be glad you kept up with the cosmetic maintenance...just sayin
  10. Replies
    29
    Views
    1,811

    Go ride on the Basin side , thats across the road...

    Go ride on the Basin side , thats across the road from Doirons, some good riding over there, and , there are NO "no wake" zones that I know of. I cant go till July 9th - 13th..............maybe Joey...
  11. Replies
    10
    Views
    814

    this mod will not help you unless you are...

    this mod will not help you unless you are planning on the Maptuner-X with its higher RPM. been there done this mod on my 2012 VXR. just saying from my personal experience.
  12. you should really go out and ride the ski for...

    you should really go out and ride the ski for awhile before doing mods. IMHO do a maptuner-x first and see how you like it.
  13. Replies
    62
    Views
    7,737

    Leroy said the water is dropping so you guys...

    Leroy said the water is dropping so you guys should have a nice time.
  14. my 2012 VXR used to piss acid on the paint all...

    my 2012 VXR used to piss acid on the paint all the time till I got an AGM battery. The acid never hurt the paint as I always wipe my ski down at the ramp before leaving the lake. on a side note, my...
  15. Replies
    4
    Views
    351

    yep clutch should only spin one way....need...

    yep clutch should only spin one way....need clutch , oil pump gasket and o-rings....should take about 2.5 hours. and 400 bucks for parts........dont try to force the pump cover, there is a bolt on...
  16. Before I cut the head off I would cut a slot in...

    Before I cut the head off I would cut a slot in the top of the bolt to fit a flat head screwdriver, put a wrench on the screwdriver handle and see if the bolt moves...never know. If not you can still...
  17. Replies
    18
    Views
    1,693

    I have used Amzoil marine oil exclusively in my...

    I have used Amzoil marine oil exclusively in my 2009 FZR and in my 2017 GP1800 ( 100 hrs ).....the FZR has 300 hours on it and I just put in its 3rd clutch. I have the C-3 impeller w/ HKS blow off...
  18. Replies
    13
    Views
    948

    I have used Amzoil Marine 10/40 in my 2009 FZR...

    I have used Amzoil Marine 10/40 in my 2009 FZR and in my 2017 GP with no problems at all.fyi
  19. Replies
    6
    Views
    611

    SOLD You got my last one ! Hey Ben , whats been...

    You got my last one ! Hey Ben , whats been going on !
  20. Replies
    12
    Views
    1,807

    Mud Bug = go ride around , find other ski's ,...

    Mud Bug = go ride around , find other ski's , go have a beer/wine stop or three, go to Gros to eat, get lost in the swamp. great time....us Texas guys can show you around. I been to every Mud Bug...
  21. Replies
    34
    Views
    2,197

    I was referring to https://www.timesert.com/ ...

    I was referring to https://www.timesert.com/ drilling and tapping the pipe...not the bell or trumpet..I thought I was clear ?
  22. Replies
    34
    Views
    2,197

    You guys might try removing the O2 sensor ,...

    You guys might try removing the O2 sensor , starting the ski and verifying if any water is blasting down the manifold.....we did an FZS pipe using a 24mm length time-cert and it was leaking water...
  23. Replies
    15
    Views
    755

    Man that is a nice trailer ! I like the deck on...

    Man that is a nice trailer ! I like the deck on the front for fueling and maintenance of the ski's.
    .
  24. Replies
    9
    Views
    712

    ok thanks for steering my brain.....Art at E.T. ...

    ok thanks for steering my brain.....Art at E.T. good idea.
  25. Replies
    15
    Views
    755

    If the trailer is up to it , Mud Bug is April 2nd...

    If the trailer is up to it , Mud Bug is April 2nd through 6th. Canadian Swamp king , our dearly departed brother , made the ride many times....very good ride....Morgan City Louisiana. Think about it...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4