Search

Page 1 of 16 1 2 3 4

Search: Search took 1.00 seconds.

  1. Thread: YES renewal

    by 2fast4u
    Replies
    5
    Views
    173

    There might be a third party warranty company you...

    There might be a third party warranty company you could buy more warranty for your ski. But I only recommend the OEM factory warranty. I have heard horror storys from folks who purchased third party...
  2. Replies
    24
    Views
    2,185

    Allowing these motors to idle for three to four...

    Allowing these motors to idle for three to four minutes prior to shutting them down is a good idea, especially since all the block/head water drains out after the motor is shut down . I always run my...
  3. Replies
    20
    Views
    1,468

    unless you are a expert tuner and have all the...

    unless you are a expert tuner and have all the gauges/data to make sure your tune is correct I would stay away from the self tune and just use one of there time tested tunes from Riva or Dean. A...
  4. Replies
    45
    Views
    2,425

    I think the machine work charges were $75.00 It...

    I think the machine work charges were $75.00 It was done to reduce the rotational weight so the clutch rpms would slow down faster when the clutch sprag un locked from the supercharger this helped...
  5. Replies
    16
    Views
    1,445

    when you change the original gap on a sparkplug...

    when you change the original gap on a sparkplug say from .038 (out of the box specification) to say .020 (desired plug gap) once the sparkplug has been run and heated and cooled several times the...
  6. I replaced my rivets with small stainless screws...

    I replaced my rivets with small stainless screws and stainless self locking nuts and flat washers much easier if you ever need to remove the trim again.
  7. heat it with a heat gun really hot then pry it...

    heat it with a heat gun really hot then pry it off.
  8. Replies
    172
    Views
    76,759

    Over the years lots of guys have tried this mod,...

    Over the years lots of guys have tried this mod, I have never seen anyone go back to the noise free flo because they lost speed. Tommy Jordan
  9. Replies
    7
    Views
    531

    If you do not change plugs at least buy a set and...

    If you do not change plugs at least buy a set and carry them along with your tool kit just incase you have a problem. I replace plugs and battery ever other year I put about 50 to 75 hours each year...
  10. here you go...

    here you go http://greenhulk.net/forums/showthread.php?t=117030&highlight=free+flow+w%2Fo+noise
  11. Replies
    15
    Views
    1,646

    you have not done any damage at all silicone is a...

    you have not done any damage at all silicone is a protectant/lube you should be good to go!
  12. Replies
    14
    Views
    1,800

    I would say 350 HP It takes lots of boost 21-25...

    I would say 350 HP It takes lots of boost 21-25 lbs and 9000 + rpms to make 400 hp
  13. Replies
    172
    Views
    76,759

    Bump this up , had a few pm on how to do it.

    Bump this up , had a few pm on how to do it.
  14. Replies
    4
    Views
    531

    R&D with pump stuffer kit! Order it here from...

    R&D with pump stuffer kit! Order it here from pwcperformance.com use code "greenhulk" and get a 10% discount. Tommy Jordan
  15. Replies
    7
    Views
    578

    PWC ride week of the 4th!

    I wanted to remind everyone to use extra CAUTION when you are out on the water all next week (4th of July week) Please ride safe !!!!! Tommy Jordan
  16. Replies
    19
    Views
    2,688

    If supercharger clutch or hose is off you should...

    If supercharger clutch or hose is off you should be able to see about 5500 rpms max and a speed of 50 to 55 mph, since there is no boost. If you are seeing much less rpms and speed look for some...
  17. Replies
    12
    Views
    1,049

    If charger does not spin at all , Clutch has...

    If charger does not spin at all , Clutch has locked up, replace clutch Period!
  18. Replies
    20
    Views
    2,934

    Have the dealer re check the engine to coupler...

    Have the dealer re check the engine to coupler aleighnment.
  19. Replies
    4
    Views
    364

    replace sparkplugs and re test first.

    replace sparkplugs and re test first.
  20. Replies
    8
    Views
    767

    DIY search for thread " prop bending 101"...

    DIY search for thread " prop bending 101" http://www.greenhulk.net/forums/showthread.php?t=20995&highlight=prop+bending+101
  21. If you are buying a new left over 2016 ski the...

    If you are buying a new left over 2016 ski the price you pay should be at least $1500 to $2500 less than you can buy a 2018 since it is two years old. Tommy Jordan
  22. Replies
    8
    Views
    517

    more than likely your water leak is coming from a...

    more than likely your water leak is coming from a the transom pump plate. Transom plate needs to be removed cleaned ,hull sanded and re sealed with 3m 5200. Tommy Jordan
  23. both props should work out about the same top...

    both props should work out about the same top speed, the 15/22 should work a little better on hookup on take off. I like props where the front is open up better than one that has less pitch on the...
  24. Replies
    21
    Views
    1,513

    Are you sure about the prop and part number for...

    Are you sure about the prop and part number for your ski? My solas book does NOT show a YG DF prop fitting a 2014 FX Sho ski. Tommy Jordan
  25. SOLD Guys this is a great quality ski! I have ridden...

    Guys this is a great quality ski! I have ridden with this ski several times never a problem with it, only problem I know of is keeping up with it"s massive top speed it can put out. Tommy Jordan
Results 1 to 25 of 385
Page 1 of 16 1 2 3 4