Search

Page 1 of 2 1 2

Search: Search took 1.00 seconds.

  1. Replies
    4
    Views
    243

    FS Riva and rxp 215

    Riva and rxp 215
  2. Get the next size up Torx socket and pound it in...

    Get the next size up Torx socket and pound it in there till it bottoms. Get a propane torch and heat the plug a bit and then you can remove it. Been there done that!
  3. Replies
    16
    Views
    1,735

    SOLD Thanks for the info mitsakosgt!

    Thanks for the info mitsakosgt!
  4. Replies
    23
    Views
    2,426

    Run the 48s like I said and jerry said. Bosch...

    Run the 48s like I said and jerry said. Bosch 50s will load up your bottom end and be too rich
  5. Replies
    23
    Views
    2,426

    Bosch 48s from Jerry's store work good with Riva...

    Bosch 48s from Jerry's store work good with Riva Ecu
  6. Thread: Shopping

    by Green Hulk
    Replies
    1
    Views
    367

    The forums online store ships world wide and you...

    The forums online store ships world wide and you can also buy most Riva, R&D parts and Solas impellers at a discounted price. Just enter the discount coupon code: greenhulk
    www.pwcperformance.com
    ...
  7. DOH! #-o Thats what I get for skimming the...

    DOH! #-o Thats what I get for skimming the question...





    Hook the water lines back up the same way they were when you took them off...

    Top of manifold goes to top of Jpipe, just a few...
  8. Thread: Throttle Body

    by ou812
    Replies
    11
    Views
    917

    WTB Thanks dimitris!

    Excellent seller!!!!! Highly recommended!!!!!!!!!!![/QUOTE]

    Thanks dimitris!
  9. Replies
    15
    Views
    805

    WTB Lift the ski up and get a hose with a sprayer...

    Lift the ski up and get a hose with a sprayer from front pull the the plug out from back i normally since cleaning put some dawn or joy in front of engine to clean helps a little more in process.
  10. Replies
    51
    Views
    10,747

    I get the fact that this is cutting edge...

    I get the fact that this is cutting edge technology on high performance platforms BUT, somebody needs to make these guys understand you can sell a lot more of this kind of equipment at a much lower...
  11. Replies
    20
    Views
    2,390

    Jerry, The advantage of this fuel rail is when...

    Jerry,

    The advantage of this fuel rail is when you pull the seat off and all your fellow jetski mates say "pphhhwwwoooaaaarrrr!!"

    Its boat ramp impressions.. at least 2mph gain!!
  12. Replies
    4
    Views
    374

    WTB - Parts Thanks guys I figures from most of his posts he...

    Thanks guys I figures from most of his posts he was a good bloke, just didn't want to end up with 2 of these things. Thanks skoepp, much appreciated mate.

    Also would be great if we could get...
  13. Not taking any sides here.... but they do come...

    Jay just called me because I have my work number in my email sig, he told me that thats how it came from riva, i told him it wasn't a factory cut and was obviously done with a dremel tool. He swears...
  14. Thread: Cams???

    by C Doo
    Replies
    29
    Views
    3,729

    get yourself a Rude 3 or ET race charger

    get yourself a Rude 3 or ET race charger
  15. Replies
    12
    Views
    1,422

    IF you do the waterbox,which i recommend, then...

    IF you do the waterbox,which i recommend, then you will also need the OPAS block offs too....
  16. Replies
    12
    Views
    1,422

    I've had a exhaust to stock location.. I've had...

    I've had a exhaust to stock location.. I've had riva thru hull pipe and I have riva water box thru hull.... Do it right the first time.... Go with a water box ... Easier to remove the charger as...
  17. ^^ well, i was thinking... If we get additional...

    ^^ well, i was thinking... If we get additional vin licnses after the original 4 (home version) after get the 15 total licenses allowed for the home version, being reward with the full version...
    ...
  18. Replies
    27
    Views
    18,786

    05 down, hours are on the mpem and ecu. Hours...

    05 down, hours are on the mpem and ecu. Hours displayed on the gauges come from the ecu. On 06 to 09, hours are on the ecu and the gauges, hours displayed are from the gauges. New gauges should get...
  19. Replies
    132
    Views
    19,118

    BAMMM!

    BAMMM!
  20. Replies
    79
    Views
    7,512

    I did a back to back test on my gprxp with a...

    I did a back to back test on my gprxp with a et137+4 and a rude two and they both ran 91 mph but the rude 2 felt a lil stronger off the bottom end but wasn't faster. I just stuck with the et I love...
  21. Replies
    869
    Views
    335,831

    Sticky: 1200 for a rebuild???Bro your taking it in the...

    1200 for a rebuild???Bro your taking it in the ass as a brand new charger only cost 800 give or take....A rebuild kit is 300 and if you send it to Jerry your looking at another 75 or so dollars for...
  22. Replies
    15
    Views
    1,677

    i run 48s with the 137.. runs fine.... 42s lean...

    i run 48s with the 137.. runs fine.... 42s lean out close to wot
  23. Thread: Best Hull?

    by Slow 91
    Replies
    3
    Views
    1,057

    jetmate.

    jetmate.
  24. Replies
    212
    Views
    43,022

    Not the first time someone has come along and...

    Not the first time someone has come along and copied something from Greenhulk/4Tecperformance. When you have the largest forum along with the top performance parts store, some seem to think it would...
  25. Replies
    212
    Views
    43,022

    It will be very hard for Torx to do better than...

    It will be very hard for Torx to do better than the Hulk, especially when starting to be dodgy like that.

    Find an online shop with better service than the Hulk and I will get my parts from them....
Results 1 to 25 of 37
Page 1 of 2 1 2