Search

Type: Posts; User: xlint89

Page 1 of 8 1 2 3 4

Search: Search took 0.13 seconds.

  1. Genuine Keihin carb rebuild kits I hope? We don't...

    Genuine Keihin carb rebuild kits I hope? We don't see a lot of success with aftermarket kits
  2. Replies
    2
    Views
    62

    Correct. That is exactly what it is. There is...

    Correct. That is exactly what it is.

    There is a pin hole at the top of the hose in the "L" fitting. It needs to be clear in order for it to work. The jet pump creates a negative pressure which...
  3. Replies
    5
    Views
    107

    Or it could be the speedometer tube that is...

    Or it could be the speedometer tube that is supposed to go on the pitot. white plastic nipple under the drive shaft that goes up to the MFD.
  4. I was going to suggest timing as well. I had a...

    I was going to suggest timing as well. I had a woodruff key shear and it caused a no start too. But you exchanged the magneto, so you would have seen that. How does the adjustable plastic timing cone...
  5. Replies
    4
    Views
    278

    FS SOLD Thank you

    SOLD

    Thank you
  6. Replies
    4
    Views
    278

    FS Yes, sorry, didn't see the updated post.

    Yes, sorry, didn't see the updated post.
  7. Replies
    3
    Views
    339

    FS CEN and PTO cyls

    CEN and PTO cyls
  8. Replies
    18
    Views
    1,814

    https://pps.partsland.com/OEM-Parts/Polaris-PWC-Pa...

    https://pps.partsland.com/OEM-Parts/Polaris-PWC-Parts/1995/1995___SL-650/DRIVE%20SYSTEM/index.php?N=1580859396-60274
  9. Thread: 96 slt 780 mfd

    by xlint89
    Replies
    1
    Views
    56

    It's most likely no good, but it costs nothing to...

    It's most likely no good, but it costs nothing to try.
  10. Thread: 96 slt 780

    by xlint89
    Replies
    12
    Views
    245

    Casey addressed everything for you. Skat Trak...

    Casey addressed everything for you.

    Skat Trak made most of the impellers for Polaris. The only way to know for sure if it's Polaris spec impeller or Skat trak is to look at the part number stamped...
  11. Thread: 96 slt 780

    by xlint89
    Replies
    12
    Views
    245

    Correct ^^^^^ Nu Jet impellers used a totally...

    Correct ^^^^^

    Nu Jet impellers used a totally different seal from the O ring type in the diagrams.

    What impeller do you have? Polaris, Skat trak, Solas, Nu Jet?

    How do the pump bearings...
  12. Replies
    9
    Views
    341

    No. SLT is the 3 seater and the cable is longer...

    No. SLT is the 3 seater and the cable is longer than the SL 2 seater. Unless it's the SLT 750. And even then the cable won't work because they didn't use the extended jet pump like the 780.
  13. Replies
    0
    Views
    156

    FS Stainless 6 vane stator $100 shipped

    Have a SS 6 vane pump stator with OK bearings I'd sell for $100 shipped in the U.S.
  14. Replies
    4
    Views
    278

    FS Vortex FA's for domestic $120 shipped

    Have a set of 3 Vortex Flame Arrestors that fit Keihin carbs. $120 shipped in the U.S.
  15. Replies
    4
    Views
    574

    FS - Parts Still here

    Still here
  16. Replies
    3
    Views
    339

    FS Still got 2 available

    Still got 2 available
  17. If you remove the engine from the SLT, you'll...

    If you remove the engine from the SLT, you'll know the answers for sure. (Not being a dick, just saying you have your answers in the hull.)
  18. Thread: SLT 780

    by xlint89
    Replies
    5
    Views
    191

    Most likely the oil in the carbs was oil and gas...

    Most likely the oil in the carbs was oil and gas mix, but the gas evaporated over time, leaving just the oil.

    These blue Fuji engines are quite reliable. The weak point is the fuel system. Keep...
  19. Thread: SLT 780

    by xlint89
    Replies
    5
    Views
    191

    Welcome to the Hulk. 155-160 is kind of hi...

    Welcome to the Hulk.

    155-160 is kind of hi compression. I'm wondering if the previous owner fogged the engine for extended storage and is the reason for the slightly higher compression reading?
    ...
  20. I agree. Get that 1050 you have running...

    I agree.

    Get that 1050 you have running optimally and just enjoy what you have.
  21. Replies
    8
    Views
    428

    Correct ^^^^^ 1996 SLT 700...

    Correct ^^^^^

    1996 SLT 700 Polyester/glass/foam composite dry weight 502 lbs

    1996 SLT 780 SMC dry weight 595 lbs.

    1996 SLTX SMC dry weight 615 lbs.

    The added benefit I see is the...
  22. Almost every mod you would do to a 1200cc, you...

    Almost every mod you would do to a 1200cc, you would do to a 1050cc. Higher compression, reeds, flame arrestor, carbs, etc...

    With your set up being in a Tiger Shark, I doubt most of this applies...
  23. Have you ever considered doing the Pro 785 valves...

    Have you ever considered doing the Pro 785 valves like this?
  24. So does that mean you they are no longer offered?...

    So does that mean you they are no longer offered?

    I never saw this thread and have a set of PSI cylinders that could use this set up.

    PS: Long time no see, hope everyone is doing well
  25. Absolutely correct ^^^^^^ Not much HP gain...

    Absolutely correct ^^^^^^

    Not much HP gain from just boring a 750. The 780 porting is different and that's what makes more HP.

    Just as reference 750 = 80 HP while the 780 makes 92+ HP
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4