Search

Type: Posts; User: tiderider

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Fuel pump... Clogged fuel filter..

    Fuel pump... Clogged fuel filter..
  2. Replies
    7
    Views
    432

    I spoke with them a few times and seemed...

    I spoke with them a few times and seemed knowledgeable. They do own a dyno that Riva owned in the past, they purchased it at an auction, that's what Racelab told me.... They reply to emails asap and...
  3. Scoop for a seadoo boat restrictive or Not?

    A friend has a modified seadoo speedster 150. The present air intake is 4 inches and has a riva non/gauze filter on it located within the engine compartment and close to some openings to the side by...
  4. Thread: fuel pump

    by tiderider
    Replies
    8
    Views
    223

    Should be fine if a relay was required. Its most...

    Should be fine if a relay was required. Its most likely a 320-340LPH unit. I would inspect the in tank filters, replace them and add an inline fuel filter as noted. At least fueling will be mint..
  5. Thread: fuel pump

    by tiderider
    Replies
    8
    Views
    223

    7 years old... I would upgrade it to a 340LPH...

    7 years old... I would upgrade it to a 340LPH unit and add an inline fuel filter. I installed an Aeromotive 12345 fuel filter with a 10 Micron filter. Doesn't take much to damage an engine should it...
  6. Thread: fuel pump

    by tiderider
    Replies
    8
    Views
    223

    To many variables to list.. If the tank is kept...

    To many variables to list.. If the tank is kept full all the time it will last many years due to it being lubricated and cooled properly by the fuel.. Clean filters also another variable.. Age as...
  7. Looks like I can make my own notches or slots on...

    Looks like I can make my own notches or slots on the injectors. Thank you for your experience with this issue.
  8. That's what came across my mind... I'll see if...

    That's what came across my mind... I'll see if there is 5mm to spare in the rail so the slot lines up and hopefully it will go in deep enough in the air intake manifold. Perhaps a criss cross with...
  9. OEM Fuel injector retainer clip for upgraded Bosch fuel injectors

    I am considering upgrading fuel injectors. I found a nice set of bosch injectors but the slot for sliding in the retainer clip is about 5 mm lower from the top. It is a long Injector with the orings...
  10. Replies
    6
    Views
    267

    Contact the seller and see what they say.. I...

    Contact the seller and see what they say.. I purchased an aftermarket high performance, light weight, single groove keeper, nitrate coated valves from them in the past which are still looking really...
  11. Replies
    6
    Views
    267

    It will be fine for your application. Jetskiparts.

    It will be fine for your application. Jetskiparts.
  12. Replies
    3
    Views
    155

    Solas concord have a nice one for the speedster...

    Solas concord have a nice one for the speedster 215hp its a SRX-CD-14/19
    https://www.solas.com/exec/msg.php?mid=62&cid=62&lg=E
  13. 15/20 should give you better top speed and you...

    15/20 should give you better top speed and you would maybe only lose 150 rpms. I used a solas concord 15/20 for x chargers. Exhaust upgrades for your set up nets zero gains..
  14. Thread: Tops valve

    by tiderider
    Replies
    8
    Views
    394

    Post some pictures. The ball should be in the...

    Post some pictures. The ball should be in the assembly unless the unit is split apart?
  15. Sorry, i don't understand your question. No...

    Sorry, i don't understand your question. No offense.. I installed those listed ebay (Seadoo flywheel bolts) on a seadoo 4 tec flywheel (Double gear), added red loctite and torque to 32lbft, no issues...
  16. I purchased those ebay (USA Business) bolts and...

    I purchased those ebay (USA Business) bolts and installed them in my original engine before it melted a piston. The Bolts were still intact and like new when I opened her up with 140 hours on it......
  17. Good point I guess. Sorry if i up set anyone. I...

    Good point I guess. Sorry if i up set anyone. I didn't think suggesting to by a few bolts on ebay was a concern.
  18. Did I read the ebay ad incorrectly? I thought...

    Did I read the ebay ad incorrectly? I thought ebay has them for $20 with free shipping to USA.. ? I'm sure the forum won't go bust over not selling 6 bolts...
  19. Good deal on ebay for bolts....

    Good deal on ebay for bolts. https://www.ebay.com/itm/254486749346
  20. Replies
    9
    Views
    517

    I believe the cylinder heads are the same as the...

    I believe the cylinder heads are the same as the older 4 tecs.. Check out my cylinder head with titanium retainers for the back up engine...
    ...
  21. Replies
    9
    Views
    517

    Its a joke, if your not aware...

    Its a joke, if your not aware...
  22. Replies
    9
    Views
    517

    You will have 70hp less then the 300??

    You will have 70hp less then the 300??
  23. Replies
    2
    Views
    948

    I have as follows for the starter Bendix Thrust...

    I have as follows for the starter Bendix Thrust washer
    Thickness 1mm
    ID= 12.5mm
    OD= 21.47mm

    My measurements for the Starter Bendix Belleville Spring washers are as follows
    OD= 24.77mm
    ID=...
  24. Replies
    1
    Views
    100

    Looks like they now all have the same amount of...

    Looks like they now all have the same amount of play after cleaning and removing all oil from the stems/seals. They do move slightly, very little side to side and all appear to be equal in movement....
  25. Replies
    1
    Views
    100

    Valve stem play within valve guide

    Is there a rule of thumb to when there is too must play between the valve stems and valve guide with springs off?
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4