Search

Type: Posts; User: Jonesyfxr

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    189

    We also has the holeshot mod…. But still run the...

    We also has the holeshot mod…. But still run the sensor
  2. Replies
    4
    Views
    189

    We left the lower sensor intact on our 1200R for...

    We left the lower sensor intact on our 1200R for safety reasons.
  3. Replies
    16
    Views
    542

    We are using K100 as our fuel additive of choice....

    We are using K100 as our fuel additive of choice. It comes highly recommended from local guys around here.
  4. Replies
    1
    Views
    70

    You drop the rear section of the pipe down into...

    You drop the rear section of the pipe down into the hull. Make sure the waterbox is pushed all the way to the rear. As you drop the rear stinger pipe into the hull, rotate the pipe clockwise, down...
  5. You need to use the pilot jet (low).

    You need to use the pilot jet (low).
  6. The jet size would dictate your fuel pressure. A...

    The jet size would dictate your fuel pressure. A larger jet means lower pressure and vice versa. I’d use the 90 as a starting point.
  7. Replies
    49
    Views
    3,025

    Cool. I was nervous at first because I’m used to...

    Cool. I was nervous at first because I’m used to a traditional style carb. It now that I’ve been into them… they’re not so bad.
  8. Replies
    6
    Views
    599

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=479343&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=479344&stc=1
  9. Replies
    6
    Views
    599

    Thanks Danny!!!! We have done almost every...

    Thanks Danny!!!! We have done almost every "trick" mod for speed.... It helps that my son is 155# too!!!
  10. Replies
    7
    Views
    337

    Just a crazy thought…. Could the crank phase be...

    Just a crazy thought…. Could the crank phase be that far off to cause this issue??
  11. Replies
    49
    Views
    3,025

    I ordered up the proper springs with the rebuild...

    I ordered up the proper springs with the rebuild kits to get the right popoff pressure. It seems you have the right springs installed. Did you check the arm height with a razor blade to make sure the...
  12. Replies
    7
    Views
    337

    This is a unique situation for sure. I’m anxious...

    This is a unique situation for sure. I’m anxious to see what the cause is.
  13. Replies
    10
    Views
    492

    We do all the above but I like to removed the...

    We do all the above but I like to removed the battery and bring into the house.
  14. Replies
    49
    Views
    3,025

    Looks good dude!! I asked for hydro turf...

    Looks good dude!!

    I asked for hydro turf samples and got an email stating they weren’t sending out samples due to shortages
  15. http://greenhulk.net/forums/showthread.php?t=9408

    http://greenhulk.net/forums/showthread.php?t=9408
  16. Replies
    49
    Views
    3,025

    You’re very welcome bro!!! Glad Rich hooked you...

    You’re very welcome bro!!! Glad Rich hooked you up…. He will also assist you with any questions you may have. He has been doing this for a loooooooooong time!!!
  17. I re-read your post. The tank is not supposed to...

    I re-read your post. The tank is not supposed to pressurize…. This is the check valve I was speaking of. There’s 4 fittings on the tank, as you’re aware since the sending unit was removed. 2 feed...
  18. If the RPM's hang, that's usually a sign of an...

    If the RPM's hang, that's usually a sign of an air leak in the engine somewhere. We thought we had an air leak and pressure tested the crankcase.... it passed the leak-down test. Since the ski is...
  19. Not the flapper in the tank..... on the vent...

    Not the flapper in the tank..... on the vent line.

    This is a very hard thread to follow, there's a lot going on with your ski with lots of changes at once. This makes it hard to help diagnose a...
  20. Replies
    49
    Views
    3,025

    Pretty slick. We used that area to install...

    Pretty slick.

    We used that area to install the primer. The other side will be getting the gauge.
  21. Replies
    318
    Views
    222,779

    Sticky: Idle should be set in the water and under load....

    Idle should be set in the water and under load. This will result in a higher idle on the trailer but is ok
  22. Make sure the check valve is working on the tank....

    Make sure the check valve is working on the tank.

    We followed the Oside Bill recipe and the ski runs great.

    This speed was with stock prop and 3/4 tank of fuel.
  23. Replies
    5
    Views
    144

    I see. I used the oil injection nipples.

    I see. I used the oil injection nipples.
  24. Replies
    3
    Views
    189

    http://greenhulk.net/forums/showthread.php?t=70129...

    http://greenhulk.net/forums/showthread.php?t=70129

    And this
  25. Replies
    3
    Views
    189

    http://greenhulk.net/forums/showthread.php?t=17767...

    http://greenhulk.net/forums/showthread.php?t=177671

    Do this^^^
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4