Search

Type: Posts; User: 2fast4u

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    22
    Views
    1,546

    Looking close at the photo where there thumb is I...

    Looking close at the photo where there thumb is I see heavy cavitation burns on the edge of the prop blades and also some cavitation pitting starting on the blade surface . this is caused by the...
  2. Replies
    16
    Views
    815

    when side gaping the sparkplug be care full and...

    when side gaping the sparkplug be care full and do not let the file touch the center electrode only remove material from the ground strap electrode.
  3. Replies
    16
    Views
    815

    when you change the original gap on a sparkplug...

    when you change the original gap on a sparkplug say from .038 (out of the box specification) to say .020 (desired plug gap) once the sparkplug has been run and heated and cooled several times the...
  4. Replies
    6
    Views
    367

    small fuel filters in each carb stopped up. R&R...

    small fuel filters in each carb stopped up. R&R carbs.
  5. SOLD Buy the parts from Butterbean 29512, I have had...

    Buy the parts from Butterbean 29512, I have had dealings with him in the past stand up guy for sure. Tommy Jordan
  6. Tell me more on how to mod the ride plate, Thanks

    Tell me more on how to mod the ride plate, Thanks
  7. more than likely your oem battery can not reach...

    more than likely your oem battery can not reach 100% charge.
  8. Me too, send me a pm

    Me too, send me a pm
  9. Replies
    12
    Views
    1,061

    given the fact that you stated 14 mph winds the...

    given the fact that you stated 14 mph winds the water had to be chopped up and that a lone can cost you mph. plus dealing with windy conditions cost you speed as well, since it is cool conditions now...
  10. Replies
    8
    Views
    496

    one question. what is your end desire with the...

    one question. what is your end desire with the ecm plugs and diagraham you have posted? what is your objective?
  11. Replies
    12
    Views
    1,061

    since you have valve retainers in place I would...

    since you have valve retainers in place I would raze the rev limiter to 9000 and retest ski first to see if you can get closer to 8800 to 8900 rpms if you are on the limiter hard you can not get the...
  12. Replies
    3
    Views
    141

    you might get better results if you posted this...

    you might get better results if you posted this in the 4 stroke forum more guys follow that section of the forum I think
  13. Replies
    14
    Views
    918

    clutch ,clutch , clutch, clutch that's all I have...

    clutch ,clutch , clutch, clutch that's all I have to say about that!
  14. Replies
    14
    Views
    918

    replace clutch again, use only Yamaha lube oil!

    replace clutch again, use only Yamaha lube oil!
  15. follow your vent line from tank up and be sure it...

    follow your vent line from tank up and be sure it is not pinched or kinked . also check valve in vent line should have a arrow on it pointing to gas tank showing a flow going to tank.
  16. you need to repost this in the Yamaha 4 stroke...

    you need to repost this in the Yamaha 4 stroke section to get better reply, How ever there should never be a vacuum in your fuel tank. some moderate pressure as the check valve will let air in and...
  17. Replies
    12
    Views
    775

    just clutch, pump gasket, o rings (4) and banjo...

    just clutch, pump gasket, o rings (4) and banjo washers (4) O ring and washers can be reused but I like to replace them to prevent any kind of leak. plus it never hurts to have spares just incase...
  18. I replaced my rivets with small stainless screws...

    I replaced my rivets with small stainless screws and stainless self locking nuts and flat washers much easier if you ever need to remove the trim again.
  19. Replies
    15
    Views
    1,044

    SOLD You can buy this from dif2001. great honest guy...

    You can buy this from dif2001. great honest guy to deal with. No Junk sold by him. Tommy Jordan
  20. Replies
    10
    Views
    341

    5 to 5.5 Mpg is about all you can get at 5000...

    5 to 5.5 Mpg is about all you can get at 5000 rpms cruzing and avoid full throttle starts on a stock tune ski.
  21. I did not say a torch, use a heat gun. once the...

    I did not say a torch, use a heat gun. once the glue has been heated extreamly hot and then cools it will release from the hull.
  22. heat it with a heat gun really hot then pry it...

    heat it with a heat gun really hot then pry it off.
  23. Replies
    12
    Views
    624

    That is the way Yamaha does there part numbers...

    That is the way Yamaha does there part numbers when they make a design to a part number.
  24. Replies
    172
    Views
    75,353

    I have found that if you sand most of the threads...

    I have found that if you sand most of the threads smooth (leaving only small ridges )on the plug before u install it and tighten the clamp good it will not leak
  25. Replies
    172
    Views
    75,353

    Over the years lots of guys have tried this mod,...

    Over the years lots of guys have tried this mod, I have never seen anyone go back to the noise free flo because they lost speed. Tommy Jordan
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4