Search

Type: Posts; User: xlint89

Page 1 of 8 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    5
    Views
    105

    Agreed ^^^^^^

    Agreed ^^^^^^
  2. Replies
    7
    Views
    92

    I have never seen one of those plastic pick ups....

    I have never seen one of those plastic pick ups.

    That blackish looking one is what I've always seen. It's really brass once cleaned up.

    I wonder if you can or would want to swap over to the...
  3. Replies
    2
    Views
    79

    Correct ^^^^. Round part mounted in upper left...

    Correct ^^^^.

    Round part mounted in upper left corner when looking from the rear. A single hex head screw usually secures it.
  4. Replies
    22
    Views
    299

    Posting in the other guys thread jogged my...

    Posting in the other guys thread jogged my memory. Did you verify exhaust valves were installed correctly?
  5. Replies
    6
    Views
    115

    Welcome. The SS 6 vane pump is very common....

    Welcome.

    The SS 6 vane pump is very common. Nothing unusual there.

    All Polaris pumps use a wedge between the pump and exit nozzle. Make sure it's installed correctly though. Thin part at the...
  6. Wow, where did all the solid couplers go? Only...

    Wow, where did all the solid couplers go?

    Only found this one doing quick search. https://www.ebay.com/itm/1995-Polaris-SLT-750-Stock-OEM-PTO/163802175803?hash=item26235ed93b:g:ZnoAAOSwXlpcfagj...
  7. Replies
    22
    Views
    299

    Try riding it with the seat off first. (easiest...

    Try riding it with the seat off first. (easiest thing to do) That should allow any exhaust gas to escape before limiting RPM.

    Next check the valves and make sure they are all in sync and opening...
  8. Got a link? Aluminum factory replacement would be...

    Got a link? Aluminum factory replacement would be new to me.
  9. It's a good chance you sucked up a rock or...

    It's a good chance you sucked up a rock or something causing the pump to not spin and causing the threads to wipe out.

    Those couplers are all over Ebay if no one on here has one for sale.

    The...
  10. Replies
    22
    Views
    299

    Did you pressure test the exhaust pipes?

    Did you pressure test the exhaust pipes?
  11. Replies
    7
    Views
    92

    Spot on ^^^^^^^ Should have 2 brass fittings...

    Spot on ^^^^^^^

    Should have 2 brass fittings with screens on them. One that runs to the bottom and the second one that sits a little above the bottom as mentioned above.

    Shouldn't be any...
  12. Don't buy the cheap plastic ones from Ebay. Of...

    Don't buy the cheap plastic ones from Ebay. Of the 2 I bought, the lever broke when I tried to "snap" the cable drum into it like the OEM.

    And the 2nd one keeps popping out because it can't have...
  13. Keep the old plugs in there. It's easier to...

    Keep the old plugs in there.

    It's easier to "read" an older plug then new. It takes a while for color to form on new plugs.

    I prefer reading wash as opposed to plugs. Plugs have lied to me...
  14. Looks like old/previous damage to me from the...

    Looks like old/previous damage to me from the pics of the head.

    Cen is just about ideal wash for maximum performance. Mag looks to be just a tad leaner than I would like.

    Would prefer to see...
  15. You are most likely correct in assuming that. ...

    You are most likely correct in assuming that.

    You can perform a leak down test to confirm if you really want to know for sure. Honestly, you should perform one after you do the crank seals to...
  16. See if any of the Ebay sellers would split the...

    See if any of the Ebay sellers would split the pump from the impeller. Might save you some $$ doing it that way.
  17. Need to split them. The front and rear inner...

    Need to split them.

    The front and rear inner have a lip that needs to sit inside a groove. The outer rear does not have this lip and can pop out like you have found out.
  18. Bummer. You've got quite the crater forming on...

    Bummer.

    You've got quite the crater forming on that piston. Looks like you were running lean = heat and may have cooked the bearing directly beneath that crater.

    Make sure your oil pump and...
  19. Randy is the one who posted that, he is a tuning...

    Randy is the one who posted that, he is a tuning guru. I would absolutely trust his posts.

    http://greenhulk.net/forums/showthread.php?t=15473

    I've never used a bore scope. I've always used a...
  20. Tough to see with the light reflecting off the...

    Tough to see with the light reflecting off the oil residue.

    What is the "door slamming" noise?

    Here's a good thread about wash. http://greenhulk.net/forums/showthread.php?t=55874
  21. Replies
    0
    Views
    117

    FS Pro 785 cylinder and piston for sale

    Got a matched cylinder and piston combo available. Cylinder and piston are in good shape but the piston does have a very slight scratch on it.

    Matched set, so no break in needed. Just mount it up...
  22. Replies
    3
    Views
    422

    FS - Parts Still got this

    Still got this
  23. I'd look for a SS 6 vane pump. Decent upgrade for...

    I'd look for a SS 6 vane pump. Decent upgrade for the little $$ it costs. Slight performance gain and better reliability over the aluminum
  24. Replies
    5
    Views
    228

    I think you need to post prices in "for sale...

    I think you need to post prices in "for sale threads".
  25. Thread: 1996 SLX 780cc

    by xlint89
    Replies
    7
    Views
    113

    Yes they do

    Yes they do
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4