Search

Type: Posts; User: Rodsatheart

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    218

    Did you try swapping the bed plate ? You'll also...

    Did you try swapping the bed plate ? You'll also need to use a 04 style drive coupling on the engine.
    Any swap is possible. Your going to need a 1100 style coupling on the driveshaft, and eventually...
  2. The knock sensor code was a issue if I remember...

    The knock sensor code was a issue if I remember right, and was a ecu issue. There was a guy that you can send your ecu to and he would fix it. I'll see if I can find his info.
  3. Sounds like it's not on the bunks right. Post a...

    Sounds like it's not on the bunks right. Post a picture looking at the bunk boards from the stern. If it's not centered on the bunk, your not going to get it on the bow stop correctly.
  4. Replies
    4
    Views
    729

    Might be the contacts in the stop button. Pull it...

    Might be the contacts in the stop button. Pull it off and see if you can get to them. If so, clean by sanding with 2000 wet dry paper and apply some dielectric grease on reassembly.
  5. https://www.manualslib.com/manual/1381029/Kawasaki...

    https://www.manualslib.com/manual/1381029/Kawasaki-Jet-Ski-Ultra-Lx.html
  6. .006-.011...

    .006-.011
    http://greenhulk.net/forums/attachment.php?attachmentid=454690&stc=1
  7. A vacuum pump will help you find the leak. Could...

    A vacuum pump will help you find the leak. Could have a pinhole somewhere. Pull the line off the fuel pump and plug it, then pull the on and res lines off the tank and apply vacuum to them one at a...
  8. Replies
    3
    Views
    275

    To me, sounds like it's dropping the bucket to...

    To me, sounds like it's dropping the bucket to far.

    http://greenhulk.net/forums/attachment.php?attachmentid=454337&stc=1
  9. Thread: Oil pumps

    by Rodsatheart
    Replies
    7
    Views
    264

    I haven't had any issues yet, and I much prefer...

    I haven't had any issues yet, and I much prefer it over std vinyl tubing. I did a kawi 750ss rebuild a few years back. It has changed owners several times, and up until the last owner pulled the pump...
  10. Most all that I read say a total mix of 32:1 for...

    Most all that I read say a total mix of 32:1 for the first tank. I break in hard after the first hour of run time, but that's me. The 750 I built a few years back is still going strong after multiple...
  11. Your doing a great job Sean, THANK YOU =D>, and...

    Your doing a great job Sean, THANK YOU =D>, and keep it up :gnorsi:. Your knowledge (along with the others) and perseverance around here does not go unnoticed. It's a pain in the butt, and a...
  12. Thread: Oil pumps

    by Rodsatheart
    Replies
    7
    Views
    264

    The oil pumps on 2 strokes are just about built...

    The oil pumps on 2 strokes are just about built proof (so to speak). People get scared off because of the oil lines breaking or coming off, but with regular inspections that can be pretty much...
  13. Replies
    1
    Views
    144

    Well at least a carb rebuild is a whole lot...

    Well at least a carb rebuild is a whole lot easier than dealing with a coil or coil wire.
  14. Replies
    4
    Views
    173

    Yes, each cyl. has it's own coil. They are in the...

    Yes, each cyl. has it's own coil. They are in the electrical box. try trimming the plug lead about 1/2". Have you tried new plugs, or at least swapping them around to make sure it's not the plugs ?...
  15. Replies
    3
    Views
    154

    Don't need to split them apart. Get a mikuni pop...

    Don't need to split them apart. Get a mikuni pop off gauge to verify needle pop off. Reuse the old needle springs. Do one carb at a time so parts don't get mixed up between them. Don't get the...
  16. Replies
    11
    Views
    350

    https://www.manualslib.com/manual/1191952/Kawasaki...

    https://www.manualslib.com/manual/1191952/Kawasaki-1100-Stx-D-I.html
  17. Replies
    11
    Views
    350

    I would check to see if the injectors are firing....

    I would check to see if the injectors are firing. You can here them click when cranking. If not, might check the crank sensor.
  18. Replies
    4
    Views
    259

    Don't think your going to find carbs on a fuel...

    Don't think your going to find carbs on a fuel injected engine.
    Spraying either on the outside of the flame arrestor only creates a hazard. Most fuel injection systems are designed to go into flood...
  19. Replies
    1
    Views
    147

    Try trimming the plug wires about 1/2". May just...

    Try trimming the plug wires about 1/2". May just need new plug wires. They don't last forever and can be replaced with some solid core wire. Some parts stores have plug wire sets for older tractors...
  20. Replies
    87
    Views
    1,710

    Both should have the carbs rebuilt, but...

    Both should have the carbs rebuilt, but especially the one that is having issues. You should also look at replacing the oil injection lines.
    Slow to return to idle could be a air leak, lean...
  21. Replies
    1
    Views
    144

    There are gel coat repair kits for small nicks...

    There are gel coat repair kits for small nicks and such. You also might get a hold of U S composites and see what they have. I've seen the repair kits on ebay and around the web, just can't remember...
  22. Replies
    8
    Views
    416

    I would take a measurement from the bed plate to...

    I would take a measurement from the bed plate to the end of the coupling, remove the plate from the engine, drop it in the hull and see how it sits.
  23. Replies
    23
    Views
    612

    Better than a broken rod going through the case. ...

    Better than a broken rod going through the case. :)
  24. Replies
    3
    Views
    186

    Are there any other lights coming on, like maybe...

    Are there any other lights coming on, like maybe the temp ? Have you reached down to test the temp of the water from the pisser, and how strong is the stream ? The Di's are common to the cooling...
  25. I'm assuming you know Mikuni makes 30, 60, and...

    I'm assuming you know Mikuni makes 30, 60, and 100psi popoff gauges ?
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4