Search

Type: Posts; User: Myself

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    1
    Views
    75

    Hmmmm....I've been through thousands upon...

    Hmmmm....I've been through thousands upon thousands of parts this year alone and don't have that problem. Sounds like you need to switch suppliers.
  2. Replies
    3
    Views
    83

    Leaking intercooler? Spraying a bit of water only...

    Leaking intercooler? Spraying a bit of water only at high rpm?
  3. Replies
    3
    Views
    128

    I've always packed them with red tacky. Never had...

    I've always packed them with red tacky. Never had any issues.
  4. Thread: 1997 1100 stx

    by Myself
    Replies
    6
    Views
    137

    Yes. Maybe it's a 99.

    Yes. Maybe it's a 99.
  5. Thread: 1997 1100 stx

    by Myself
    Replies
    6
    Views
    137

    I have a customer with a '98 STX 1100 with 425...

    I have a customer with a '98 STX 1100 with 425 hours on it and has never been apart! I just put a cdi on it a couple weeks ago, compression still 115psi on all 3!!
  6. Not an '18 but I just had to fix a stator...

    Not an '18 but I just had to fix a stator connection on a '14 with 34 hours! The triangular statr plug was never fully seated from the factory. Outside looked good, inside the pins were burnt off!
  7. Replies
    3
    Views
    101

    Have you tried new spark plugs?

    Have you tried new spark plugs?
  8. Replies
    1
    Views
    66

    2-Stroke I use thus...

    I use thus stuff.....https://www.homedepot.com/p/PC-Products-PC-11-1-lb-Paste-Epoxy-160114/100649621
    It works great. After full cure spray some white appliance epoxy paint over it.
  9. Check with Westside Powersports. I believe they...

    Check with Westside Powersports. I believe they also keep new parts in stock. Jess is at Lake of the Ozarks and he can rush it if you want?
  10. Replies
    8
    Views
    205

    Did you try new spark plugs first?

    Did you try new spark plugs first?
  11. Replies
    0
    Views
    58

    Gp1300 rough idle and low top speed.

    I did the d-plate and chip, power valve keepers, and some other maintenance to this 1300 early this year. It seems the idle is too low and top speed was only in the low 50's. Plugs show a good color,...
  12. Replies
    11
    Views
    297

    Many skis do it at slower speeds. The early Kawi...

    Many skis do it at slower speeds. The early Kawi stx hull does it BAD just up on plane. The '97 and up Seadoo XP also does it pretty bad about 25-30 mph. You just get used to it.
  13. Replies
    6
    Views
    157

    You can throttle it on the trailer. Maybe it will...

    You can throttle it on the trailer. Maybe it will show up. Yes, the shaft is press fit into the bearing housing. No need to pull the pump. The driveshaft is just splined into the midshaft. Sometimes...
  14. Lots of options for boat tachs. Many have...

    Lots of options for boat tachs. Many have adjustable "pulse per rev" switch to work with many different engine configurations.
  15. Replies
    3
    Views
    168

    After degreasing and wire wheeling all threads, I...

    After degreasing and wire wheeling all threads, I use a drop of blue threadlocker on every bolt.
  16. Replies
    6
    Views
    157

    What???? Not on a '96 model, that's only 23 years...

    What???? Not on a '96 model, that's only 23 years old!!!! Lol!
  17. Replies
    10
    Views
    8,032

    I've done 2 951's this past week and have another...

    I've done 2 951's this past week and have another one sitting here to do. I amost never replace the fuel return line. Even when the green goo is everywhere on the supply side, the return is good. At...
  18. Replies
    11
    Views
    379

    Sounds like a no spark on one cylinder. There...

    Sounds like a no spark on one cylinder.
    There are a couple common issues I find on these old triples. First check all coils. You can ohm from the boot to ground (around 10k ohm) and ohm at the coil...
  19. Replies
    13
    Views
    857

    Probably mis stamped and packaged wrong. Guessing...

    Probably mis stamped and packaged wrong. Guessing the ckearance would be ok if you stuck those in a std bore cylinder.
  20. Replies
    1
    Views
    74

    No, either one on either carb, they pump the same.

    No, either one on either carb, they pump the same.
  21. Replies
    9
    Views
    312

    Maybe they plow a little but I guess you guys...

    Maybe they plow a little but I guess you guys have never ridden a waveblaster 2.....lol! Ride one of those then let me know if your Kawi still dunks the nose!
  22. Shorland'r used to make one particularly narrow...

    Shorland'r used to make one particularly narrow but still heavy duty. I have one and have seen several around here....
  23. I fixed one this season leaking badly from the...

    I fixed one this season leaking badly from the bottom of the front oil pump housing. It was tough to find cause the oil was running down and spreading out across the lower case dripping everywhere. I...
  24. I call that scuffing. Mic the piston on the skirt...

    I call that scuffing. Mic the piston on the skirt just below the wrist pin. Then mic the cylinder. You need to know the difference in thousandths for clearance. If you can hone it some more and stay...
  25. It's fine, been using it in customers sc machines...

    It's fine, been using it in customers sc machines for a few years.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4