Search

Type: Posts; User: T0MMY B0NES

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    14
    Views
    604

    2-Stroke SBT

    Finally got her opened up, can confirm that powervalves have been updated, the rods are stamped SBT, and cylinders are sleeved.
  2. Replies
    14
    Views
    604

    2-Stroke Mikuni

    Mikuni carb kit arrived, splurged and got the kit that came with 2 needle valves.
    http://greenhulk.net/forums/attachment.php?attachmentid=450790&stc=1
  3. Ha, I hear ya, fault of mine I guess. To me, the...

    Ha, I hear ya, fault of mine I guess. To me, the job ain't finished until it works and looks good. So don't soak the carbs in carb cleaner...can we soak in something like Purple Power or Simple Green...
  4. What is the easiest way? I have new oil seals and...

    What is the easiest way? I have new oil seals and was planning on breaking down the motor. How can I confirm crank bearings are reusable? Spinning and looking for play, listening for grinding,...
  5. Purchased aftermarket by mistake, but Bay Area...

    Purchased aftermarket by mistake, but Bay Area Powersports is taking the return and sending out genuine Mikuni.
    Being told the engine looks ok, I purchased a +1mm rebuild kit, looks like by...
  6. What is the best way to clean the engine and carb...

    What is the best way to clean the engine and carb now that they are removed from the hull and separated?
  7. Interesting.

    Interesting.
  8. Replies
    14
    Views
    604

    2-Stroke Bad Reed, just replace the petals on that side or...

    Bad Reed, just replace the petals on that side or all petals or just buy used cage set?
    Returning the aftermarket carb kit and needles and genuine Mikuni being shipped, thanks for catching.
    So you...
  9. 800 XLT 66e Torn Down - Identify any issues from pistons or head?

    Finally got the engine broken down a bit. Pulled head, carbs, and reeds. Ski suffered from low compression in the #2. Got a build thread in the appropriate forum that no one looks at. Ha.

    FIRST...
  10. Replies
    14
    Views
    604

    2-Stroke Break It Down Damn It!!!! 66e 800 XLT

    Been a minute, not like anyone is following or answering my questions, but I'll keep you people posted anyways!!!
    Got some time to break down the 66e engine a bit. Ski #2 had low compression on the...
  11. Replies
    11
    Views
    1,606

    Hope this thread isn't "too dead", I am working...

    Hope this thread isn't "too dead", I am working on a pair of '03 XLT 800's. Sounds like I may be having to big bore to 81, how will this affect the carb settings?
  12. Replies
    302
    Views
    169,895

    Sticky: Is this possible on a 2003 XLT 800? Or just the...

    Is this possible on a 2003 XLT 800? Or just the GP's?
  13. Replies
    5
    Views
    640

    Name checks out.

    Name checks out.
  14. Replies
    14
    Views
    604

    2-Stroke Engine and Parts

    Workbench built, engine is sitting on it ready for breakdown. Also got a bunch of parts in, still need to order a used oil pump and I am thinking about just replacing the starter while I have the...
  15. Well damn. They are sitting where they fell off....

    Well damn. They are sitting where they fell off. Not sure if I can find the exact locations or not. Thanks for the heads up.
  16. The motor is free and ready to be broken down...

    The motor is free and ready to be broken down once I get a workbench built. Removal of the stator housing was the answer to the above post. I did find some oil in the cover of the stator housing, not...
  17. Replies
    14
    Views
    604

    2-Stroke The motor is free and ready to be broken down...

    The motor is free and ready to be broken down once I get a workbench built. Removal of the stator housing was the answer to the above post. I did find some oil in the cover of the stator housing, not...
  18. So remove the flywheel cover and that will free...

    So remove the flywheel cover and that will free the wires from the engine side?
  19. I was afraid to yank it out, I pulled on it...

    I was afraid to yank it out, I pulled on it pretty good and it didn't want to budge. I was afraid even getting the grommet out of the box that the black plug would be too big to come through the box...
  20. Engine is in the air BUT still hooked up HELP '03 XLT 800

    I have a "Build" thread over on the Builds Sub-forum...

    So, as you can see by the pictures, motor is on the cherry picker but I am still hooked to electrical box. I have been following the Engine...
  21. Replies
    14
    Views
    604

    2-Stroke Engine is in the air...but still connected...Help.

    So, as you can see by the pictures, motor is on the cherry picker but I am still hooked to electrical box. I have been following the Engine Removal manual that SBT produced for the Yamaha 800 and it...
  22. Replies
    14
    Views
    604

    2-Stroke The negative starter motor bolt is a BEAR to get...

    The negative starter motor bolt is a BEAR to get to. I have removed the 10mm nut from the positive but any tips on accessing the neg cable bolt is much appreciated. Thinking about cutting it, I am...
  23. Replies
    14
    Views
    604

    2-Stroke Clean Garage and Tools

    Been a minute, had to get the garage and tools cleaned up and organized to make it a bit more efficient for a project of this caliber. I am just a few steps away from pulling the engine out, went to...
  24. Replies
    14
    Views
    604

    2-Stroke Moving Along

    Erickson sling and Pittsburgh (HF) Cherry Picker worked great this evening. Redneck carts held up great as well.

    Ski # 2 will be the first ski up as it had the most notable issues. Pulled plugs...
  25. Replies
    14
    Views
    604

    2-Stroke Ordered Erickson 1000 lb. sling and picked up a 2...

    Ordered Erickson 1000 lb. sling and picked up a 2 ton cherry picker from the parking lot sale at Harbor. Picker will be assembled today and the sling arriving tomorrow. I hope to have ski # 2 on the...
Results 1 to 25 of 27
Page 1 of 2 1 2