Search

Type: Posts; User: 2fast4u

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    6
    Views
    272

    small fuel filters in each carb stopped up. R&R...

    small fuel filters in each carb stopped up. R&R carbs.
  2. SOLD Buy the parts from Butterbean 29512, I have had...

    Buy the parts from Butterbean 29512, I have had dealings with him in the past stand up guy for sure. Tommy Jordan
  3. Tell me more on how to mod the ride plate, Thanks

    Tell me more on how to mod the ride plate, Thanks
  4. more than likely your oem battery can not reach...

    more than likely your oem battery can not reach 100% charge.
  5. Me too, send me a pm

    Me too, send me a pm
  6. Replies
    12
    Views
    889

    given the fact that you stated 14 mph winds the...

    given the fact that you stated 14 mph winds the water had to be chopped up and that a lone can cost you mph. plus dealing with windy conditions cost you speed as well, since it is cool conditions now...
  7. Replies
    8
    Views
    455

    one question. what is your end desire with the...

    one question. what is your end desire with the ecm plugs and diagraham you have posted? what is your objective?
  8. Replies
    12
    Views
    889

    since you have valve retainers in place I would...

    since you have valve retainers in place I would raze the rev limiter to 9000 and retest ski first to see if you can get closer to 8800 to 8900 rpms if you are on the limiter hard you can not get the...
  9. Replies
    3
    Views
    123

    you might get better results if you posted this...

    you might get better results if you posted this in the 4 stroke forum more guys follow that section of the forum I think
  10. Replies
    14
    Views
    864

    clutch ,clutch , clutch, clutch that's all I have...

    clutch ,clutch , clutch, clutch that's all I have to say about that!
  11. Replies
    14
    Views
    864

    replace clutch again, use only Yamaha lube oil!

    replace clutch again, use only Yamaha lube oil!
  12. follow your vent line from tank up and be sure it...

    follow your vent line from tank up and be sure it is not pinched or kinked . also check valve in vent line should have a arrow on it pointing to gas tank showing a flow going to tank.
  13. you need to repost this in the Yamaha 4 stroke...

    you need to repost this in the Yamaha 4 stroke section to get better reply, How ever there should never be a vacuum in your fuel tank. some moderate pressure as the check valve will let air in and...
  14. Replies
    12
    Views
    744

    just clutch, pump gasket, o rings (4) and banjo...

    just clutch, pump gasket, o rings (4) and banjo washers (4) O ring and washers can be reused but I like to replace them to prevent any kind of leak. plus it never hurts to have spares just incase...
  15. I replaced my rivets with small stainless screws...

    I replaced my rivets with small stainless screws and stainless self locking nuts and flat washers much easier if you ever need to remove the trim again.
  16. Replies
    15
    Views
    1,032

    SOLD You can buy this from dif2001. great honest guy...

    You can buy this from dif2001. great honest guy to deal with. No Junk sold by him. Tommy Jordan
  17. Replies
    10
    Views
    324

    5 to 5.5 Mpg is about all you can get at 5000...

    5 to 5.5 Mpg is about all you can get at 5000 rpms cruzing and avoid full throttle starts on a stock tune ski.
  18. I did not say a torch, use a heat gun. once the...

    I did not say a torch, use a heat gun. once the glue has been heated extreamly hot and then cools it will release from the hull.
  19. heat it with a heat gun really hot then pry it...

    heat it with a heat gun really hot then pry it off.
  20. Replies
    12
    Views
    604

    That is the way Yamaha does there part numbers...

    That is the way Yamaha does there part numbers when they make a design to a part number.
  21. Replies
    172
    Views
    74,985

    I have found that if you sand most of the threads...

    I have found that if you sand most of the threads smooth (leaving only small ridges )on the plug before u install it and tighten the clamp good it will not leak
  22. Replies
    172
    Views
    74,985

    Over the years lots of guys have tried this mod,...

    Over the years lots of guys have tried this mod, I have never seen anyone go back to the noise free flo because they lost speed. Tommy Jordan
  23. Replies
    12
    Views
    604

    It was my understanding the bolt from a 2015 and...

    It was my understanding the bolt from a 2015 and up sc ski has a bigger hole in it than a 2009 , the factory up graded this hole size.
  24. Replies
    2
    Views
    129

    That is a 1200 gpr grate, the gpr 800 grates are...

    That is a 1200 gpr grate, the gpr 800 grates are closed in more on the back corners where the water enters the ramp.
  25. Replies
    5
    Views
    213

    I suppect your shaft is Not the Problem. If your...

    I suppect your shaft is Not the Problem. If your shaft is I would only use OEM parts. More than likely you prop is the problem
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4