Search

It is also replaced by a resistor. so do not worry. if there were problems, the engine would not start. if the temperature sensor is faulty, there is no spark.

Hello. tell me I'm looking at the photo and can't find the difference in the head gasket, can you see which holes are enlarged in the picture? Where did you connect the hose from the third...

I am writing for people whose servo does not open when moving on water. but the trailer is being tested to open close, everything is as written in the manual. the problem is solved only by...

never do that. your engine will not run normally. it could break your pistons. they are different and open at different engine speed. I went through this on my 1200 with the drive set from 800...

All I found 2 threads on this forum in which everything is clear.

why do you need to grind it, if you say you need to put washers? the back is where the speed sensor is, as I understand it.

Can anyone explain to me what needs to be done with the ride plate. I read the forum, we are told that we need to shrink something and put washers. but I am using google translator and do not...

http://greenhulk.net/forums/attachment.php?attachmentid=472330&stc=1Привет, я правильно понял, вы об этом спрашивали?

👌

I didn't call you an idiot. I use google translate, so the meaning of my messages is not conveyed correctly. your starter must always cling to the flywheel, it does not. and if it slips when there...

I'm of course sorry and I'm from Russia. but what are you doing? you twist your hand when the candle is installed and show us that it stops, it is clear to the idiot that it stops, because there is...

what was the point of shooting visible with the head removed? you still haven’t answered when the engine does not turn with the starter with the spark plug installed, can you turn it by hand?

I will write again that in case of a problem with the cylinder, you would not have a starter spinning, but in the video you have it spinning. if the starter is spinning, then the bendix is spinning....

judging by the sound in the second video, the bendix does not catch on the flywheel. this means that the bendix is ​​not fast enough to open. try connecting the plus directly to the starter.
if...

http://turbomaxx.free.fr/GP1200R/LIT-18616-02-15.pdf

By analogy with a car, you need to use all the electrical wires from the old motor and rearrange them to the new one.all wires and control box from the new motor do not need to be used.

what's the difference what its specification is? the engine is the same. do as indicated on the forum.

thanks for the answer. the only thing I didn't check was the fuel cock. next season I will plug the hoses bypassing it.

how are you going to use the 80mm piston on Nikasil? what number is written on your cylinder responsible for its size? the clearance should be written in the instructions for that piston. I think...

That's why I asked this question. can the pressure differ when checking with the assembled pump? I've always checked everything assembled and ended up running out of fuel. is it possible that I...

http://greenhulk.net/forums/showthread.php?t=290476&page=2&highlight=Pop-off
read this thread. it says that it is impossible to measure pop off with an installed fuel pump

if the resistance is the same, then everything is in order with him. I am engaged in the sale of this type of parts. your problem is different. when you turn on the ignition it will move a little...

thanks for the answer. yes I know all this. done. problem if I use spring 95 then the pop-off will be only 30. and if I use 115 the spring pop-off will be 40. that's why I'm asking about the...

Hello everyone. and so my problem is due to lack of fuel. I recently read on the forum that the pressure of the pop off should be measured with the pump removed, that is, apply pressure directly to...

As a spark owner I often read forums, there is an official spark forum. and he has one factory problem - a crookedly installed engine, which subsequently cuts off the splines of the crankshaft or...