Search

Type: Posts; User: casey67

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Welcome to Greenhulk. Pretty sure it was Watcon...

    Welcome to Greenhulk.
    Pretty sure it was Watcon that had the accel pumps. They are located in Wisconsin, an internet search should find the info.
  2. That is correct, only has low speed mixture...

    That is correct, only has low speed mixture screws.

    Polaris only had 1 early model with high speed mixture screws-most manuals show that early model carb, which is incorrect 99 0/0 of the time.
    ...
  3. Replies
    17
    Views
    375

    Polaris speedometers can be VERY INACURATE. I...

    Polaris speedometers can be VERY INACURATE. I would never do repairs according to the speedo alone. Because of the speedo's I use a GPS whenever I ride .

    With out a load on the engine,minor...
  4. Replies
    5
    Views
    152

    99 was the first year for the gen3 ignition and...

    99 was the first year for the gen3 ignition and only in the 1200 which will only be the Genesis and X45.
    The stator works like aN "update" stator but has a different seal at housing and wires do not...
  5. Replies
    6
    Views
    291

    I deffinitely agree with your focus on mid range....

    I deffinitely agree with your focus on mid range.

    I don't think any stock 700 saw 54-55 in the Midwest. I saw 50 with my stock Hurricane IF ...IF it stopped proposing. When landing at those...
  6. Replies
    6
    Views
    291

    Yeah, it's amazing what that little twin is...

    Yeah, it's amazing what that little twin is capable of, especially in a small craft.

    I ran a 13/18 in my Cane for the short time I had it. In my opinion the Cane is a "low speed"-"lots of turns"...
  7. Replies
    12
    Views
    223

    So now it looks like the CDI did wake up somehow,...

    So now it looks like the CDI did wake up somehow, but possibly still not triggered by the stator.
    Stator test should reveal if stator is capable of signaling the CDI.
  8. Replies
    12
    Views
    223

    3 volts on red/pur with the connecter connected ?...

    3 volts on red/pur with the connecter connected ? That's not good. But the red/pur is for the charging system, will still need to get corrected. The black wire will ground the stator-that could keep...
  9. Replies
    9
    Views
    255

    You've been around long enough to know K447...

    You've been around long enough to know K447 probably covered that subject..lol
    https://sites.google.com/site/polarispwcknowedge/Home/first-things-to-do

    Links in his signature should have the...
  10. Replies
    12
    Views
    223

    Ok, you have power to the CDI but looks like the...

    Ok, you have power to the CDI but looks like the CDI is not "waking up".

    There is an inline 12 pin connecter going to the stator, about 10-12 inches from Ebox. Check the pins and terminals for...
  11. Replies
    12
    Views
    223

    Hoping for 11v on red/pur and around 8v on brown.

    Hoping for 11v on red/pur and around 8v on brown.
  12. Replies
    12
    Views
    223

    Welcome to Greenhulk. Start by testing voltage...

    Welcome to Greenhulk.
    Start by testing voltage while cranking at the CDI, measure from the red with purple stripe wire to the black wire at the CDI box in the electrical box.
    Also measure voltage...
  13. Replies
    2
    Views
    100

    Yes there should be a hose there, that will run...

    Yes there should be a hose there, that will run to the bottom of that "C" shaped pipe, just past the end of the "C" bend.

    That fitting on the pipe will unscrew, it is important to check the screen...
  14. Hey Dayton, Welcome to GreenHulk. A picture of...

    Hey Dayton, Welcome to GreenHulk.
    A picture of YOUR electrical box will be best to proceed.

    Yes the thin black wire at the LR does cround the LR and electrical box half. But it is attached by the...
  15. Replies
    14
    Views
    360

    Yeah, in theory it's nice to see the ignition is...

    Yeah, in theory it's nice to see the ignition is capable of jumping a giant gap. With parts that are not new ,the spark will find the path of least resistance-rubbed plug wire-dry rotted plastic coil...
  16. Replies
    11
    Views
    242

    The large black cable goes directlty from the neg...

    The large black cable goes directlty from the neg battery post to the engine case. Left rear.

    Was the solenoid an exact replacement. Pretty sure it mounts in the electrical box.
  17. Replies
    1
    Views
    84

    The 3/4 hose could be routed as needed or get 90...

    The 3/4 hose could be routed as needed or get 90 degree elbows from a hardware store.

    The exhaust hose if I remember correctly is 2 3/4,possibly 2 7/8. I have used silicone 90 degree elbows that...
  18. Replies
    11
    Views
    242

    Welcome to GreenHulk. The red flashing light...

    Welcome to GreenHulk.

    The red flashing light will not keep it from cranking. The fuel sender float will over time loose it's ability to float in gas. The float can be replaced, usually cost about...
  19. Replies
    14
    Views
    360

    3/8 gap is huge. Plug gap is .024-.025. Spark at...

    3/8 gap is huge. Plug gap is .024-.025. Spark at the plugs is what matters-so not sure what the question is.
  20. Replies
    46
    Views
    1,334

    Hmm. Could you post a few pictures of the CDI ?...

    Hmm. Could you post a few pictures of the CDI ?
    I'm wondering if it is one of the aftermarket CDI's.

    Cool to hear you got it figured out and the "stove fix" worked. I have a couple CDI that...
  21. Replies
    46
    Views
    1,334

    Was the elect box flooded ?

    Was the elect box flooded ?
  22. Thread: LR-503 repair?

    by casey67
    Replies
    19
    Views
    2,220

    And NEVER leave it that way. The bypass is for...

    And NEVER leave it that way. The bypass is for testing ONLY !
  23. Replies
    15
    Views
    391

    The black wire at the 12 pin connecter for MFI.

    The black wire at the 12 pin connecter for MFI.
  24. Replies
    15
    Views
    391

    If it has good ground at the connecter, MFI is...

    If it has good ground at the connecter, MFI is likely bad.
    Using a test light would be best-.
  25. Replies
    2
    Views
    161

    Get a magnifying glass. Each fitting will have a...

    Get a magnifying glass. Each fitting will have a 3 letter abbreviation for what it does.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4