Search

Type: Posts; User: GTXX

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    9
    Views
    2,983

    Brian Baldwin also won the Sea Doo Bounty...

    Brian Baldwin also won the Sea Doo Bounty competition today, that's a big deal!
  2. Replies
    86
    Views
    13,243

    some were asking about the piston weight...

    some were asking about the piston weight difference, going to a lighter piston is OK without rebalancing. A reciprocating part's weight has less of an effect on engine balance than rotating part do,...
  3. Replies
    12
    Views
    2,107

    FS that's not where you determine the throttle bore,...

    that's not where you determine the throttle bore, measure at the throttle shaft.
  4. Replies
    12
    Views
    4,102

    Congratulations Duane! looks like a nice set up!...

    Congratulations Duane! looks like a nice set up! http://www.jetthrustperformance.com/
  5. Replies
    30
    Views
    2,309

    it does burn well, smokes a little though...

    it does burn well, smokes a little though...
  6. Thread: 2010 RXT-X

    by GTXX
    Replies
    4
    Views
    1,324

    It all depends on where the dealer is in the US,...

    It all depends on where the dealer is in the US, it does take a couple of months beginning late January/early Febuary before all dealers have receive all that they ordered. I have no idea how...
  7. Replies
    62
    Views
    12,685

    I think the engine ID number is also stamped into...

    I think the engine ID number is also stamped into the case halves at the PTO end. The cover has to be removed to see them, maybe someone with more experience than me tearing into these motors could...
  8. Replies
    177
    Views
    23,321

    I've always heard the same thing but the pump...

    I've always heard the same thing but the pump nozzle on the X ski is a lot bigger than the non-X ski, but the steering nozzle is the same part. I guess there are exceptions, maybe because the X pump...
  9. the spring that holds the bucket up could have...

    the spring that holds the bucket up could have popped off or broke
  10. Not saying that isn't what happened, but if the...

    Not saying that isn't what happened, but if the reverse bucket came down at 77mph I would have expected to see the plastic bucket and linkage part broken before the pump nozzle, that's what I've seen...
  11. Replies
    30
    Views
    2,309

    cut the top deck off of it, mount a seat in it...

    cut the top deck off of it, mount a seat in it and give it to the kids with a paddle.
    If I were posed with this problem I would clean up the tree limbs and dead trees laying in the woods around the...
  12. Replies
    13
    Views
    1,618

    Riva's will break too edited to add that I...

    Riva's will break too

    edited to add that I know of only one retainer breaking, anything can break or be broken.....;)
  13. Replies
    59
    Views
    6,138

    kind of makes you think about installing used...

    kind of makes you think about installing used rings. if they have been ran 20 hours or so and don't have a huge end gap you could say they aren't defective....
  14. Replies
    4
    Views
    728

    WTB beginning in 2006 the cams are all the same from...

    beginning in 2006 the cams are all the same from 155 hp and up.
  15. Replies
    12
    Views
    4,120

    I kinda doubt that motor could even push a...

    I kinda doubt that motor could even push a surfboard to 100mph
  16. Replies
    231
    Views
    18,065

    Blame it on 10,000 different things, IMO when the...

    Blame it on 10,000 different things, IMO when the economy is like this people just have to not do everything they would like to do. If I had the money I would have competed in every one of the...
  17. Thread: What a d-bag

    by GTXX
    Replies
    4
    Views
    881

    seems like I read the 98 hose is NLA...

    seems like I read the 98 hose is NLA...
  18. Replies
    25
    Views
    2,849

    and make sure it's a fine grit the shop uses, a...

    and make sure it's a fine grit the shop uses, a coarse grit finish will slow you down
  19. Thread: Cylender bore

    by GTXX
    Replies
    7
    Views
    856

    if the dish volume is adjusted so the compression...

    if the dish volume is adjusted so the compression is the same and the weight is within tolerance, shouldn't hurt a thing.
  20. Replies
    37
    Views
    5,732

    isn't the braking system controlled by the ski's...

    isn't the braking system controlled by the ski's electronics?
  21. Thread: RXPX SC Question

    by GTXX
    Replies
    9
    Views
    1,015

    thought everyone was blocking the extra oil...

    thought everyone was blocking the extra oil passage because oil blows by the seal on some?
  22. Replies
    2
    Views
    620

    hmmm.... I'm thinking that you will need to go...

    hmmm.... I'm thinking that you will need to go to a dealer and have the ski connected to BUDS to program the keys. check all hose clamps, oil level, check anything you can for correct assembly.
  23. Replies
    16
    Views
    3,159

    Most likely the head you buy from Riva is the...

    Most likely the head you buy from Riva is the same head that PPG would sell you, Riva is also a Sea Doo dealer. PPG being $60 less for the same part...
  24. Replies
    16
    Views
    3,159

    sounds like a bargain. any stipulations on the...

    sounds like a bargain. any stipulations on the core condition?
  25. Replies
    16
    Views
    3,159

    no experience with a head but they Rotax reman...

    no experience with a head but they Rotax reman stuff for 2-strokes has always been top shelf-like new. How much is it?
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4