Search
Type: Posts; User: polaris junky
Search: Search took 0.00 seconds.
-
06-27-2020, 04:17 PM
Thread: MSX 150 No ETB response
by polaris junky- Replies
- 5
- Views
- 418
I think I have a bad wire somewhere. Everytime I...
I think I have a bad wire somewhere. Everytime I unplug and plug everything back in a different error of some sort. Once low voltage to ETB, next EBT out of range, then no response from the EBT or...
-
06-27-2020, 03:29 PM
Thread: MSX 150 No ETB response
by polaris junky- Replies
- 5
- Views
- 418
That problem fixed now.....throttle valve...
That problem fixed now.....throttle valve learning: position out of range.
-
06-27-2020, 03:24 PM
Thread: MSX 150 No ETB response
by polaris junky- Replies
- 5
- Views
- 418
Alright, the EBT now is moving again but I still...
Alright, the EBT now is moving again but I still have a check engine light. The code is saying battery voltage too low during relearn process. It is at 12.7. I will put the charger on it and will...
-
06-27-2020, 08:48 AM
Thread: MSX 150 No ETB response
by polaris junky- Replies
- 5
- Views
- 418
Well that is the one part I didn't try yet, PPU...
Well that is the one part I didn't try yet, PPU module and ETB didn't help. I thought with the PPU voltage changes the PPU was ok but I will swap it out sometime this weekend. Thanks!
-
06-25-2020, 03:33 PM
Thread: MSX 150 No ETB response
by polaris junky- Replies
- 5
- Views
- 418
MSX 150 No ETB response
I have been struggling with my one of my MSX150s. I have installed the ECU in a properly functioning one, everything worked fine. Now back in the troubled one, the fuel pump was not kicking in when...
-
08-19-2018, 06:22 PM
- Replies
- 2
- Views
- 397
Like Casey said, check all hoses but I would bet...
Like Casey said, check all hoses but I would bet from sitting so long your thru-hull bearing seal is shot.
Look down at the drive shaft after the coupler were the driveshaft goes out through the... -
08-18-2018, 07:58 PM
Thread: MSX please help
by polaris junky- Replies
- 29
- Views
- 2,470
Autozone has them for $54 in the US. You can...
Autozone has them for $54 in the US. You can order them on-line from them, just search Bosch 0261230042
-
08-15-2018, 07:19 PM
Thread: MSX please help
by polaris junky- Replies
- 29
- Views
- 2,470
Are you sure it wasn't coming from the thru hull...
Are you sure it wasn't coming from the thru hull bearing seal?
-
08-10-2018, 03:56 PM
- Replies
- 15
- Views
- 1,517
My sensors were OEM pierburg and bosh not...
My sensors were OEM pierburg and bosh not aftermarket as well, just bad out of the box. I think maybe dealer returns maybe, not sure. Also there was no check engine light. The upper map sensor...
-
08-10-2018, 12:39 PM
- Replies
- 15
- Views
- 1,517
I had a similar issue with mine a few weeks ago,...
I had a similar issue with mine a few weeks ago, It was around 6500rpm though. I ended up getting a bad wastegate solenoid and bad map sensor from autozone. They replaced them no problem and...
-
08-08-2018, 08:06 PM
- Replies
- 14
- Views
- 1,045
I had a strange one with a SLTX recently. It was...
I had a strange one with a SLTX recently. It was non-updated over 100 hours and all of a sudden if you tried to go above 4900ish rpms it would cut out and die. Limped it back about 2 miles like...
-
07-29-2018, 09:35 AM
Thread: Hydro-Turf SLTX Seat Cover and Mats
by polaris junky- Replies
- 6
- Views
- 991
FS I'll take it! Great deal!
I'll take it! Great deal!
-
07-12-2018, 12:36 PM
Thread: MSX 150 Boost
by polaris junky- Replies
- 5
- Views
- 572
It seems to be the issue....with the stock...
It seems to be the issue....with the stock original 'old' style one it would go into overboost/limp mode so I think everything is good.
Yes I have to hold up on the wastegate to get full boost, I... -
07-12-2018, 12:16 PM
Thread: MSX 150 Boost
by polaris junky- Replies
- 5
- Views
- 572
I have another Pierburg coming today, not sure of...
I have another Pierburg coming today, not sure of what color it will be. Also have a grey version that is Dorman brand to try.
-
07-12-2018, 12:14 PM
Thread: MSX 150 Boost
by polaris junky- Replies
- 5
- Views
- 572
Hose from the turbo to the mteal inlet fitting,...
Hose from the turbo to the mteal inlet fitting, the 90 degree up fitting that air blows through without power to actuator. The fitting parallel to the valve remains open. I disconnected the...
-
07-11-2018, 06:49 AM
Thread: MSX 150 Boost
by polaris junky- Replies
- 5
- Views
- 572
MSX 150 Boost
Good morning. I have a MXS 150 that was going into overboost. So I ordered a new solenoid for replacement. Pierburg 7.22240.13.0, arrived not working at all on the ski or bench testing. Received...
-
09-04-2017, 06:21 PM
Thread: Polaris Hurricane
by polaris junky- Replies
- 6
- Views
- 1,728
SOLD Went down and noticed the thin ground was...
Went down and noticed the thin ground was connected to the battery, removed and nothing.....so original ignition.
-
09-04-2017, 05:03 PM
Thread: Polaris Hurricane
by polaris junky- Replies
- 6
- Views
- 1,728
SOLD I don't believe so, the small black wire is still...
I don't believe so, the small black wire is still on the negative post. I have never had the box apart, I will see of he remembers updating it.
-
09-03-2017, 05:19 PM
Thread: Polaris Hurricane
by polaris junky- Replies
- 6
- Views
- 1,728
SOLD Bliss, NY about 45 minutes from Rochester
Bliss, NY about 45 minutes from Rochester
-
08-23-2017, 05:04 PM
Thread: Polaris Hurricane
by polaris junky- Replies
- 6
- Views
- 1,728
SOLD Polaris Hurricane
For sale, hurricane in great shape MFD says 25.5 hours. I am selling for my father in law, he is looking for $2500 ???
-
07-21-2017, 02:48 PM
Thread: Slt750 water box getting very hot
by polaris junky- Replies
- 5
- Views
- 557
Check the inlet at the jet pump. Smaller hands...
Check the inlet at the jet pump. Smaller hands can reach in the nozzle and there is a screen or 2 small holes right were the 1"-ish tube is on the right side for the water feed. The weeds are bad...
-
07-19-2017, 06:41 PM
Thread: One of the original
by polaris junky- Replies
- 1
- Views
- 309
One of the original
My wife''s grandfather owned a polaris dealership for years. Here is one of the SL650's with the wetsuit to match 25 years later and only about 5 hours on the machine.
-
07-17-2017, 08:52 AM
Thread: 785 Pro help
by polaris junky- Replies
- 13
- Views
- 1,520
Big thanks to lugs for hooking me up with a new...
Big thanks to lugs for hooking me up with a new pto headpipe. The pro is running like a champ now!!! These things are amazing.
-
07-13-2017, 02:23 PM
- Replies
- 16
- Views
- 1,759
If you are careful about gas/fumes/and fiberglass...
If you are careful about gas/fumes/and fiberglass you can always use a grinder with a cut wheel to slice the bearing in half. Even if you can't cut it all the way you should be able to split it the...
-
07-10-2017, 06:29 AM
Thread: 94 Polaris SL750 Help
by polaris junky- Replies
- 4
- Views
- 916
Did you trim back the plug wires? Does fuel drip...
Did you trim back the plug wires? Does fuel drip or spray in the carbs when you press the throttle?
Results 1 to 25 of 56
So....for all of you changing your own oil...important question. My ski is...
DIY oil changes, Is it really...