Search

Type: Posts; User: snipe243

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    375

    FS 2009 yamaha fzr riva stage 3 fully built

    CHECK THIS OUT ON EBAY.

    SOLD
    ...
  2. Replies
    4
    Views
    229

    This sounds exactly what happened to me when the...

    This sounds exactly what happened to me when the clutch was starting to slip,,
  3. Replies
    22
    Views
    1,913

    4-Stroke I was curious why you went with that pitch, I’m...

    I was curious why you went with that pitch, I’m running a stage 3 on my FZR and its had a 15/23 which I’m on the rev limit very quickly at 86mph, thinking of changing to 15/24 or 25
  4. I would think your dealer would work with you to...

    I would think your dealer would work with you to fix The problem, at least offer some form of financial assistance, not sure how it works in EU
  5. I HOPE you are right, there has to be something...

    I HOPE you are right, there has to be something better than these clutch driven superchargers
  6. :smt119:smt119 BRING IT ON!

    :smt119:smt119 BRING IT ON!
  7. Replies
    12
    Views
    1,645

    View Post

    I壇 negotiate out the most you can get and cut your losses,, it will never be what it was,,,
  8. Replies
    13
    Views
    518

    Definitely use their info, guys on here have...

    Definitely use their info, guys on here have already spent the money and made the mistakes, their advise is golden!
  9. Replies
    28
    Views
    3,092

    Get your prop straightened out and inspect your...

    Get your prop straightened out and inspect your wear ring,, that should make an improvement
  10. Replies
    19
    Views
    2,195

    I would think a tune on your stage 2 with a...

    I would think a tune on your stage 2 with a higher rev would do what you want and still run cool and reliable
  11. Replies
    9
    Views
    1,741

    Try the Riva thru hull exhaust, they really rumble

    Try the Riva thru hull exhaust, they really rumble
  12. Replies
    21
    Views
    1,264

    Easy to understand install, just not a lot of...

    Easy to understand install, just not a lot of room to work. Add an intercooler and get your revs up to get the most out of stage 1
  13. Replies
    18
    Views
    18,107

    Some water in hull is normal, rough riding will...

    Some water in hull is normal, rough riding will add more so installing a dedicated bilge running off a manual switch will give you some peace of mind
  14. This was a good read,, lots of helpful...

    This was a good read,, lots of helpful information on a similar problem Ive had
  15. If the cable is disconnected I would think the...

    If the cable is disconnected I would think the nozzle will float around under power, which I don’t think would work so well. I have seen the oem cables for a lot less than $400,, shop around
  16. Replies
    10
    Views
    527

    Cam timing is very important, but a simple check...

    Cam timing is very important, but a simple check would be to install new plugs no matter what they look like, I’ve seen new looking plugs be fouled and cause rough idle
  17. Replies
    1
    Views
    93

    With that many hours the least i would consider...

    With that many hours the least i would consider is truing up the cylinders and installing new piston and rings, throughly inspect head, timing chain and valves. If not doing yourself would cost about...
  18. Thread: High rev FZR

    by snipe243
    Replies
    10
    Views
    496

    R&D ride plate and intake grate

    R&D ride plate and intake grate
  19. Thread: High rev FZR

    by snipe243
    Replies
    10
    Views
    496

    You are correct, 160mm scat swirl at 15/23

    You are correct, 160mm scat swirl at 15/23
  20. Thread: High rev FZR

    by snipe243
    Replies
    10
    Views
    496

    High rev FZR

    I知 running a fully built 2010 FZR with Riva Stage 3, R&D R4 flash. Pulls great on the low end but I知 on the 8800 rev limiter almost instantly, gps 81mph. My question is, I知 currently running 15/23...
  21. SOLD Does you supercharger have any touch downs on the...

    Does you supercharger have any touch downs on the galouth?
  22. Replies
    2
    Views
    154

    I’m currently running a Riva E2 at 16psi. This...

    I’m currently running a Riva E2 at 16psi. This thing rips hard down low and tops out very quickly bouncing off the rev, thinking a better pitch would put me a lot faster and keep me off the rev. I...
  23. Replies
    2
    Views
    154

    Prop pitch on fully built FZR

    Totally rebuilt new short block with new Carrillo racing rods and pistons, titanium valve retainers, Riva cylinder head and main bolts, Riva stage 3 kit . I was running an R&D R3 flash at 8750 RPM,...
  24. FS - Parts I have a C3-11 with low hrs, (25) in great...

    I have a C3-11 with low hrs, (25) in great condition, sell for $250

    this came out of my 2009 FZR, went to a 16psi after complete Riva build and
  25. Replies
    1
    Views
    351

    Noisy Yamaha FZR

    NEED HELP! Just finished up a cam shaft replacement on 2009 full RIVA build FZR, I知 running the 16lb monster wheel with C4 tune. I知 getting some noise from front of motor at idle and lower rpms,,...
Results 1 to 25 of 26
Page 1 of 2 1 2