Search

Type: Posts; User: psycho rxp

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    9
    Views
    301

    The supercharger should not spin freely, it’s...

    The supercharger should not spin freely, it’s gear driven off the fly wheel. The clutches could have let loose in the supercharger, or the fly wheel bolts sheared off. Either way the PTO cover needs...
  2. Replies
    8
    Views
    726

    Remove the spark plugs and spin it over see if...

    Remove the spark plugs and spin it over see if any of it comes out
  3. Replies
    24
    Views
    2,790

    I’d Keep the RXT Hull, as the RXP is only good...

    I’d Keep the RXT Hull, as the RXP is only good for flat water SPEED #’s . I’ve had both.
  4. Replies
    25
    Views
    1,067

    You will need aftermarket, or lightened intake...

    You will need aftermarket, or lightened intake valves, retainers, and should go open loop cooling @ 8800 RPM +

    Also look into getting pressure reliefs installed in the pump tunnel, to keep the...
  5. I would look into your DESS post first, They can...

    I would look into your DESS post first, They can go bad.
  6. Replies
    38
    Views
    1,109

    View Post

    Isnít there a check valve built into the fuel pump itself, On the pressure side?
    Did you install the relay for the Riva fuel pump?


    Iíve had one go bad before and had similar issues. The rough...
  7. Replies
    8
    Views
    261

    Just an FYI, the “E” temp is not exhaust...

    Just an FYI, the “E” temp is not exhaust temperature, “E”stands for earth temp( outside air temp)
  8. Replies
    31
    Views
    2,700

    In my case, it’s not the same cylinder , it was...

    In my case, it’s not the same cylinder , it was the middle cylinder with the issue. It is currently at the dealer, still waiting to be taken apart and diagnosed. I think the problem is most are still...
  9. Remove the glove box, and go through the top

    Remove the glove box, and go through the top
  10. Replies
    3
    Views
    222

    The 300 kit comes with the guide for the holesaw...

    The 300 kit comes with the guide for the holesaw to cut the manifold in the proper place.
  11. Replies
    37
    Views
    2,453

    19’

    19’
  12. Replies
    37
    Views
    2,453

    Yup, 42 hrs on the clock, middle cyl, flatwater...

    Yup, 42 hrs on the clock, middle cyl, flatwater River cruising at 7700 rpm when it stalled and wouldn’t restart. Let it sit a few minutes, then tried again, and the motor locked up:evil:
  13. Should have no worries on the valves, those were...

    Should have no worries on the valves, those were the 04-05 year motors , with the sodium filled exhaust valves. .
  14. Replies
    37
    Views
    2,453

    Me too. Let’s just hope the new motor will have...

    Me too.
    Let’s just hope the new motor will have some sort of upgraded valves, or I fear, this could happen again. If nothings changed on the new motor, I may be buying a set of valves to put in...
  15. Replies
    37
    Views
    2,453

    Mine dropped the middle cylinder valve, Will know...

    Mine dropped the middle cylinder valve, Will know more hopefully later this week when they pull the head, to see if it’s isolated to the intake valves, or something else :roll:
  16. Replies
    28
    Views
    1,246

    The supercharger slip could also be low, causing...

    The supercharger slip could also be low, causing it to not build full boost. Might want to check into that. They can loose some tension after they break in after the rebuild. Do you know if OEM...
  17. Can-doo Pro or Dealer only. The 05’ RXT did...

    Can-doo Pro or Dealer only.


    The 05’ RXT did not have VTS
  18. I assume you already checked all the fuses , and...

    I assume you already checked all the fuses , and changed spark plugs already?

    Have you tried a different set of known good coils yet?

    What does your compression #’s look like?

    Did you just...
  19. Replies
    31
    Views
    2,700

    They changed the cam part number in 2018, and now...

    They changed the cam part number in 2018, and now in 2019 they changed the intake valve part numbers. Since it’s only the 19’s with the issues so far, I would say it’s more towards the new valves...
  20. Replies
    125
    Views
    20,381

    I still don’t see anything, not even on Seadoo’s...

    I still don’t see anything, not even on Seadoo’s website yet.
  21. Replies
    31
    Views
    2,700

    The cam part # changed for the 18’s and haven’t...

    The cam part # changed for the 18’s and haven’t heard of any valve issues on them yet. ��
  22. Replies
    31
    Views
    2,700

    Or engines #-o

    Or engines #-o
  23. Replies
    31
    Views
    2,700

    Sounds like a Recall or some service bulletins...

    Sounds like a Recall or some service bulletins Will be coming out soon With all these low hour 19’s having valve issues already...:facepalm:
  24. Replies
    31
    Views
    2,700

    From doing a little digging, it looks like they...

    From doing a little digging, it looks like they changed the part number on the intake valves in 19’ for some reason. The intake and exhaust valves are the same from 16 to 18, but the intake valves...
  25. Replies
    14
    Views
    676

    FS - Parts :roll:=D>

    :roll:=D>
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4