Search

Type: Posts; User: scantone

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Mine was - -5.8psi @ 4000 rpm 6.7psi @ 6665...

    Mine was -
    -5.8psi @ 4000 rpm
    6.7psi @ 6665 rpm
    21psi @ 8125 rpm
    32psi @ 9200 rpm

    This is a gtx3076r gen2. 11:1 compression, e85, 100mph 18FX. Timing was at 17degrees wide open.

    *Above...
  2. The turbo might not be to big with a smaller...

    The turbo might not be to big with a smaller exhaust housing. I have a .82 on mine now, I know they make a .63 but I couldn't say how much it would move the boost down in the rpm range. Where a car...
  3. 20lbs wont be enough after a few weeks and you'll...

    20lbs wont be enough after a few weeks and you'll want more down the road......... I had the GTX3076R GEN II on my 18 FX and it came alive around 6800rpm with 11.0:1 pistons and easily puts out...
  4. Replies
    21
    Views
    2,529

    I have one on my turbo PX and have run it to 95...

    I have one on my turbo PX and have run it to 95 or so, with that said I something flexing at this speed and causing the prop to hit the wear ring. Im waiting to get a new driveshaft and eliminate...
  5. Replies
    7
    Views
    1,030

    Damn never seen a gas tank vent that big, if its...

    Damn never seen a gas tank vent that big, if its 3/4 id say your fine on that end.
  6. Replies
    7
    Views
    1,030

    Gas tank vent is hole is no where near big enough...

    Gas tank vent is hole is no where near big enough if thats what you used.........
  7. Replies
    25
    Views
    4,252

    I get 85-86ish no retainers 13/20 dont know rpm...

    I get 85-86ish no retainers 13/20 dont know rpm dont care. I do run the riva intercooler with the same plate salt water tampa area fu**in hot out.
  8. Replies
    14
    Views
    1,165

    FS - Parts After this weekend hes gonna be ordering the...

    After this weekend hes gonna be ordering the entire riva catalog
  9. Replies
    21
    Views
    1,795

    Hes already been to my house to borrow the...

    Hes already been to my house to borrow the maptuner..................:smt100
  10. Replies
    22
    Views
    1,397

    Might sell mine but 10k aint buyin...

    Might sell mine but 10k aint buyin it...........PM if your serious.
  11. My man getting good with photoshop!!!!! She did...

    My man getting good with photoshop!!!!! She did pretty good after your dataeyeing and revisions :smt119
  12. Replies
    95
    Views
    10,899

    Did say it's not, but them rpms are rollin!

    Did say it's not, but them rpms are rollin!
  13. Replies
    95
    Views
    10,899

    That's not a stock wheel unless you pulling...

    That's not a stock wheel unless you pulling 10000+ rpm
  14. Lol not this again

    Lol not this again
  15. Replies
    16
    Views
    2,237

    Riva grate blows stock away, I even modified the...

    Riva grate blows stock away, I even modified the 19 stock and riva still outperforms it without question.
  16. Replies
    9
    Views
    1,188

    As weird as it is and I agree but it somehow...

    As weird as it is and I agree but it somehow works. Did about a 3 mile wide open pull with this and the new riva intercooler a little while back and the ski fluctuate from 83 to 84 the entire time....
  17. Replies
    35
    Views
    6,527

    We seal the intake grate 100% to the hull, then...

    We seal the intake grate 100% to the hull, then the rideplate also gets sealed where they meet and have not had this issue with a GP, mine mid-80s Gus was 90s. We do have a friend that rides with the...
  18. Works great so far no heat fade or mph loss over...

    Works great so far no heat fade or mph loss over a few mile run. Install was simple and clean, I did the pro cooling at the same time. Real test will come this summer in the Tampa heat and humidity....
  19. Replies
    301
    Views
    48,321

    What nozzle are you using?

    What nozzle are you using?
  20. Replies
    52
    Views
    5,590

    Turdz

    Turdz
  21. Replies
    192
    Views
    18,497

    Trifflin

    Trifflin
  22. Replies
    86
    Views
    13,677

    If you do it the way I told you no you will not...

    If you do it the way I told you no you will not use a sleeve the entire plastic manifold remains intact. All your removing is the ribbon and sanding down the lip that holds the ribbon. Once you do it...
  23. Replies
    86
    Views
    13,677

    You can do that also with the stage 1 non...

    You can do that also with the stage 1 non aggressive tune as well. Last time I checked they run the same timing up top with the agr being advanced in the mid portions of the map.
  24. Replies
    86
    Views
    13,677

    Your last gp mods in your profile pic, good call...

    Your last gp mods in your profile pic, good call sticking to cup holders
  25. Replies
    86
    Views
    13,677

    Wife said not happening

    Wife said not happening
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4