Search

Type: Posts; User: mittens

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    70
    Views
    3,421

    That's a 3/4 link 3 middle & 4 outside. That's...

    That's a 3/4 link 3 middle & 4 outside. That's the walk one.
    4/5 is the 16 up one
  2. Replies
    25
    Views
    5,235

    sod you swap over any parts or just strait whole...

    sod you swap over any parts or just strait whole head springs & all
  3. Replies
    4
    Views
    286

    You can buy a Captains call Y with valve used....

    You can buy a Captains call Y with valve used. and plumb it. I have thought about it too ha.

    Could use factory water box and exit on one side, and on side would allow you to skip waterbox all...
  4. Replies
    25
    Views
    5,235

    This sucks at any point but that's low hours for...

    This sucks at any point but that's low hours for it I would think
  5. Replies
    13
    Views
    442

    Some are installing 4/5link chain from 2016 up,...

    Some are installing 4/5link chain from 2016 up, and spinning them on the stock 14-15 gears. Cheap insurance..
  6. Replies
    2
    Views
    78

    WTB I have one with Water sock, mount, everything. ...

    I have one with Water sock, mount, everything. came off my FZ. was installed at 16 hours, and removed at 42. so 26 hours. no scratches or anything.
  7. Replies
    13
    Views
    442

    I know of stories where they did not fix it. and...

    I know of stories where they did not fix it. and I also know of once where they have. I also when shopping had people tell me Yamaha fixed it. with receites, and then I check part numbers and Yamaha...
  8. Good thought. If Yamaha used old parts on the...

    Good thought. If Yamaha used old parts on the transom, wonder about that clutch. could pull charger and see. 6 bolts.
  9. Replies
    15
    Views
    7,342

    That last video gives a much better perspective...

    That last video gives a much better perspective on the drop/launch thank you.
  10. Replies
    21
    Views
    1,827

    Nice work

    Nice work
  11. Replies
    16
    Views
    525

    I bought a new housing and rebuilt it with new...

    I bought a new housing and rebuilt it with new parts, and my old shaft. OEM on the one I did.
  12. Being told the Exhaust temp/water sensor can be...

    Being told the Exhaust temp/water sensor can be just zip tied in the hull and plugged it. as it only trips when unplugged or over temp/ is this true?

    Welder put me off a this week as the 2 race...
  13. Replies
    16
    Views
    525

    Have you tried giant Vice grips and turning them...

    Have you tried giant Vice grips and turning them again? did you rip the heads off trying to un screw them?

    The thrust washer can be slid on by hand.
  14. Replies
    1
    Views
    129

    The older school set ups where using fuel...

    The older school set ups where using fuel pressure to flow more fuel out of the injectors. Then the larger injector tunes came out and can flow the fuel needed or more boost by injector sizing vs...
  15. Replies
    1
    Views
    117

    The SVHO intercooler is better then the SHO. ...

    The SVHO intercooler is better then the SHO. How much? not sure.
  16. Replies
    2
    Views
    74

    In PCB, you can launch St Andrews park (pricy...

    In PCB, you can launch St Andrews park (pricy parking but nice), or a lot of local ramps back in lower grand lagoon. The back side of shell island is good, and the front side is nice if surf is calm...
  17. Replies
    15
    Views
    7,342

    Have you done the drags? Speaking from personal...

    Have you done the drags? Speaking from personal experience?
    I agree videos sure don't look like any drop. Or moving parts.

    not being argumentative just asking.
  18. Replies
    29
    Views
    1,945

    Really trying to not do that. just more shit to...

    Really trying to not do that. just more shit to break.
  19. Replies
    29
    Views
    1,945

    Nothing?

    Nothing?
  20. Replies
    16
    Views
    525

    Totally even better. just was trying to share...

    Totally even better. just was trying to share the idea of something electric to heat each bolt one at a time with out flame inside the hull.
  21. Replies
    16
    Views
    525

    Would be using multiple kinds of penetrating oil....

    Would be using multiple kinds of penetrating oil. and could possibly heat with soldering iron holding it on each bolt for a while. Not sure if they would help or hurt but wanted to mention it as...
  22. Replies
    15
    Views
    7,342

    Yea that video looks like what I thought. just...

    Yea that video looks like what I thought. just barley some bunk and they throttle off it. its not lowering or why would they not lower it when loading ha.
  23. I know mine if it has water in it, or not shuts...

    I know mine if it has water in it, or not shuts of 30 seconds after the key. same with the dash, Have to cycle key/ button again to make it pump again. did this testing a new pump location
  24. Replies
    27
    Views
    744

    With just retainers people spinning 9000-9500.. ...

    With just retainers people spinning 9000-9500..

    if I was new to the game, tune, prop, and retainers will gain you a lot! .
  25. Replies
    27
    Views
    744

    Keep in mind if your worried about warranty keep...

    Keep in mind if your worried about warranty keep RPMS below 8k on the tune
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4