Search

Type: Posts; User: Saum700p

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    17
    Views
    632

    Learner mode and install a blow off valve to help...

    Learner mode and install a blow off valve to help with the clutch abuse.
  2. Replies
    17
    Views
    632

    You can run the motor with out boost. It would be...

    You can run the motor with out boost. It would be no different then runing it when the sc clutch goes out. Lower compression pistons are in the sc motors so don't look for any speed out of it if you...
  3. Replies
    13
    Views
    9,071

    Im running amsoil marine 10-40 and happy with it...

    Im running amsoil marine 10-40 and happy with it in both of my skis. 215 hours on the VXR and 90 on the GP. look up a guy project farm on youtube. he's done oil comparisons. you can make your own...
  4. Replies
    80
    Views
    12,710

    Pulled the pump on my '18 gp and measured the...

    Pulled the pump on my '18 gp and measured the back side of the pump. 6.3" which is 160mm. Compared the outlet of the pump to the nozzle on my '18 Vxr. Identical. So the 6 vane, 8 vane and the new...
  5. Replies
    12
    Views
    1,183

    8,500 seems to be the the agreed point to go to...

    8,500 seems to be the the agreed point to go to Ti retainers to be safe. When should you be looking at springs and dual springs? Anyone with good information on this?
  6. Replies
    80
    Views
    12,710

    It seems information on this pump was just...

    It seems information on this pump was just released prematurely for pre-orders on bad information. It seems like a good piece, just not what it was marketed as.
  7. Replies
    80
    Views
    12,710

    Agreed... This is the same "pump", just a...

    Agreed... This is the same "pump", just a different housing and wear ring setup.
  8. Replies
    8
    Views
    428

    Post some pictures so we can help you.

    Post some pictures so we can help you.
  9. Replies
    126
    Views
    6,075

    Tommy, +1! The movie is Cannonball Run..... ...

    Tommy, +1! The movie is Cannonball Run.....

    Where are the hookers? HA
  10. View Post

    Sounds like your crank is 180 out.
  11. Replies
    29
    Views
    8,005

    Only way to truly find out what works for your...

    Only way to truly find out what works for your setup is to put something in and try it. You'll get 20 different thoughts but your water, air, weight, engine mods, and tune will all combine for a...
  12. Replies
    13
    Views
    616

    Thats right 16 and 17, but they are all one tight...

    Thats right 16 and 17, but they are all one tight assembly as long as the sprag isn't damaged. I knew they came off together when I tore mine down for a sheared key but could remember exactly. But...
  13. Replies
    13
    Views
    616

    if I remember correctly 16, 17 & 18 are bolted...

    if I remember correctly 16, 17 & 18 are bolted together with the 6 flywheel bolts. There should be no movement between them and they should press tight onto the crahnkshaft. Replace the 6 flywheel...
  14. Replies
    13
    Views
    616

    Yes, you just need to make sure the mating...

    Yes, you just need to make sure the mating surface isn't damaged.
  15. Replies
    13
    Views
    616

    Ski won't run? Ignition timing is off? If so,...

    Ski won't run? Ignition timing is off? If so, your stub shaft which tightens the flywheel down is loose. I had this happen on my '18 VXR earlier this year. Motor has to com out the flywheel key...
  16. Replies
    126
    Views
    6,075

    I agree were all in contact with the people who...

    I agree were all in contact with the people who bitch about skis. With that said its about how you ride. I have the loudest ski around. Its infamous. But when you ride you can control how obnoxious...
  17. Replies
    14
    Views
    897

    I did not. Cavitated and was slower off the line...

    I did not. Cavitated and was slower off the line then a buddy of mine with a stock impeller. My experience with the vxr was that you need to have a target rpm under 8,000. Above that all I did was...
  18. Replies
    126
    Views
    6,075

    cjk. You don't want any of what you're...

    cjk. You don't want any of what you're starting.... just saying
  19. Replies
    11
    Views
    759

    If you're turning 8,600 you should have retainers...

    If you're turning 8,600 you should have retainers in now regardless if you want to turn it up to 9,000.
  20. Replies
    42
    Views
    2,097

    Take pictures and videos. following

    Take pictures and videos. following
  21. Replies
    126
    Views
    6,075

    Pretty much have two options a riva or a stock...

    Pretty much have two options a riva or a stock one back in from here. I have two stock ones for sale if you decide to go that route. I have riva's on my vxr and my Gp. The vxr is pretty obnoxious but...
  22. Replies
    14
    Views
    897

    I ran an 11/15 on my 18 tuned vxr. Sat on the...

    I ran an 11/15 on my 18 tuned vxr. Sat on the 8,300 rpm limiter at 65 mph. You are going to need more angle than that on an impeller. Id go with the 13/19 have it trued and bent down to a 13/18...
  23. I believe all the older plates are the same. ...

    I believe all the older plates are the same. They did change for the 19's but the older plates bolt up to the 19's so you should be completely fine the soho and ho hulls are the same so the...
  24. Replies
    14
    Views
    1,702

    I like ride... I have a vxr and gp and do like...

    I like ride... I have a vxr and gp and do like them but have ridden my buddy's fzr. I did like his fzr and would probably prefer the fzr if it had ride.
  25. Jeff As soon as you make the first rip what ever...

    Jeff As soon as you make the first rip what ever protectant that has piled up in your pump will be blown out. there is a tremendous amount of pressure in there when riding. If you are having issues...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4